Docomo f-01c Instruction Manual page 138

Upper slot : Command
Lower slot : Example
*1
AT&E<n>
AT&E1
OK
AT&F
AT&F
OK (When in offline mode)
*1
AT&S<n>
AT&S0
OK
AT&W
AT&W
OK
AT＊DANTE
AT＊DANTE
＊DANTE : 3
OK
*2
AT＊DGANSM=<n>
AT＊DGANSM=0
OK
*2
AT＊DGAPL=<n> [,<cid>]
AT＊DGAPL=0,1
OK
*2
AT＊DGARL=<n> [,<cid>]
AT＊DGARL=0,1
OK
*2
AT＊DGPIR=<n>
AT＊DGPIR=0
OK
AT＊DRPW
AT＊DRPW
＊DRPW : 0
OK
AT+CAOC
AT+CAOC
+CAOC : "000024"
OK
AT+CBC
AT+CBC
+CBC : 0,100
OK
Set the speed display used when connection is made.
n=0 : Display communication speed of wireless zone
n=1 : Display communication speed between a PC and FOMA terminal (default)
Reset the current setting to the default.
When this command is executed during communication, the terminal is reset after the line
is disconnected (displaying "NO CARRIER").
Set control of the data set ready (DR) signal to be output to DTE.
n=0 : Always ON (default) n=1 : ON at time of connection
Register the current settings in FOMA terminal.
Indicate FOMA terminal reception level in the "＊DANTE : <n>" format.
n=0 : Out of service area n=1 : Received signal level of FOMA terminal is 0 or 1 antenna.
n=2 : Received signal level of FOMA terminal is 2 antennas.
n=3 : Received signal level of FOMA terminal is 3 antennas.
AT＊DANTE=? : Display a list of displayable values
Set to reject or permit incoming packet communications.
n=0 : Reject setting = OFF, Accept setting = OFF (default)
n=1 : Reject setting=ON n=2 : Accept setting=ON
AT＊DGANSM? : Display current settings
AT＊DGANSM=? : Display a list of assignable values
Set the dialup connections (APN) to permit incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN permitted for incoming communications
n=1 : Delete from list of APN permitted for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT＊DGAPL? : Display current settings
AT＊DGAPL=? : Display a list of assignable values
Set the dialup connections (APN) to refuse incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN rejected for incoming communications
n=1 : Delete from list of APN rejected for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT＊DGARL? : Display current settings
AT＊DGARL=? : Display a list of assignable values
Set Caller ID notification when packet communication connection is being performed. This
command is available when a communication is sent or received.
n=0 : Connect to APN directly (default) n=1 : Connect to APN prefixing 184
n=2 : Connect to APN prefixing 186
When Show/Hide caller ID is specified by dialup network→P20
AT＊DGPIR? : Display current settings
AT＊DGPIR=? : Display a list of assignable values
Indicate an index for the reception power of the radio waves that FOMA terminal receive.
AT＊DRPW=? : Display a list of displayable values
Display last call cost.
Display FOMA terminal's battery level in the "+CBC : <bcs>,<bcl>" format.
bcs=0 : Powered by the battery pack bcs=1 : Not powered by the battery pack
bcs=2 : Battery pack removed bcs=3 : Power-supply error
bcl=0 : No battery remained or battery pack removed bcl=1-100 : Battery remained
AT+CBC=? : Display a list of displayable values
Description
32