D Convenient Functions For Transmit - Icom IC-7000 Instruction Manual

D Convenient functions for transmit

• Transmit quality monitor (p. 87)
➥ Push [AF( )], then [F-4 OTH] to enter the
set
miscellaneous (others) Set mode. Select an item
with [F-1 ≤]/[F-2 ≥], then rotate [DIAL] to turn
the monitor function ON or OFF.
• VOX (voice operated transmit) (p. 83)
➥ While "M-3" is selected, push [F-1 VOX] to turn
the VOX function ON or OFF.
• Hold down [MENU/GRP] for 1 second once or twice
to select the menu group M.
• Push [MENU/GRP] momentarily one or more times
to select the menu M-3.
• " " appears when the VOX function is set to ON.
➥ While "M-3" is selected, hold down [F-1 VOX] for
1 second to enter the VOX Set mode.
• Push [F-1 ≤]/[F-2 ≥] to select an item.
• Rotate [DIAL] to set the value/conditions.
D About the 5 MHz frequency band operation (USA version only)
Operation on the 5 MHz frequency band is allowed
on 5 discrete frequencies and must adhere to the
following:
• The USB, USB Data, CW and PSK modes
• Maximum of 100 watts ERP
• 2.8 kHz bandwidth (maximum)
It is your responsibility to set all controls so that
transmission in this frequency band meets the
stringent conditions under which amateur operations
may use these frequencies.
NOTE: We recommend that you store these
frequencies, modes and filter settings into memory
channels, for easy recall.
To assist you in operating within the rules specified
by the FCC, transmission is illegal on any
frequencies other than the five shown in the tables
at the right.
(Effective Radiated Power)
RECEIVE AND TRANSMIT
• Speech compressor (p. 87)
➥ While "M-3" is selected, push [F-2 COM] to turn
the speech compressor ON or OFF.
• " " appears when the speech compressor is set
to ON.
➥ While "M-3" is selected, hold down [F-2 COM]
for 1 second to enter the compression level Set
mode.
• Rotate [DIAL] to adjust the compression level.
• Transmit filter width (p. 84)
➥ While "M-3" is selected, push [F-4 TBW] momentarily
to display the selected transmit filter width.
➥ While "M-3" is selected, hold down [F-4 TBW] for
1 second to select the transmit filter width from
narrow, middle and width.
• The transmit filter width window appears for showing
the selected transmit filter width each time [F-4 TBW]
is pushed.
• For the USB mode
The FCC specifies center frequencies on the 5 MHz
frequency band. However, the transceiver displays
carrier frequency. Therefore, tune the transceiver
to 1.5 kHz below the specified FCC channel center
frequency.
Transceiver Displayed
Frequency
5.33050 MHz
5.34650 MHz
5.35700 MHz
5.37150 MHz
5.40350 MHz
• For the CW mode
The transceiver displays the center frequency.
Therefore, tune the transceiver to the specified FCC
channel frequency when you operate in the CW
mode.
Transceiver Displayed
Frequency
5.33200 MHz
5.34800 MHz
5.35850 MHz
5.37300 MHz
5.40500 MHz
4
FCC Channel
Center Frequency
5.33200 MHz
5.34800 MHz
5.35850 MHz
5.37300 MHz
5.40500 MHz
FCC Channel
Center Frequency
5.33200 MHz
5.34800 MHz
5.35850 MHz
5.37300 MHz
5.40500 MHz
4
40