Yamaha DME Designer Owner's Manual page 402

Chapter 6 Component Guide
Effect Type
Amp Simulate
One input, two
output guitar amp
simulator.
Dyna.Filter
Two input, two
output dynamically
controlled filter.
Dyna.Flange
Two input, two
output dynamically
controlled flanger.
Dyna.Phaser
Two input, two
output dynamically
controlled phaser.
402 DME Designer Owner's Manual
Parameter Setting Range
AMP.Type STK-M1, STK-M2, THRASH,
MIDBST, CMB-PG, CMB-VR,
CMB-DX, CMB-TW, MINI, FLAT
DST.Type DST1, DST2, OVD1, OVD2,
CRUNCH
Drive 0 to 100
Master 0 to 100
Bass 0 to 100
Middle 0 to 100
Treble 0 to 100
Cab Dep 0 to 100%
EQ F 100 to 8.0 kHz
EQ G -12 to +12 dB
EQ Q 10.0 to 0.10
N.Gate 0 to 20
Sense 0 to 100
Direction UP, DOWN
Decay 44.1kHz: 6.0ms to 46.0s
48kHz: 5.0ms to 42.3s
88.2kHz: 3ms to 23.0s
96kHz: 3ms to 21.1s
Type LPF, HPF, BPF
Offset 0 to 100
Reso. 0 to 20
Level 0 to 100
Sense 0 to 100
Direction UP, DOWN
Decay 44.1kHz: 6.0ms to 46.0s
48kHz: 5.0ms to 42.3s
88.2kHz: 3ms to 23.0s
96kHz: 3ms to 21.1s
Offset 0 to 100
FB.Gain -99 to +99%
LSH F 21.2 Hz to 8.00 kHz
LSH G -12 to +12 dB
EQ F 100 Hz to 8.00 kHz
EQ G -12 to +12 dB
EQ Q 10.0 to 0.10
HSH F 50.0 Hz to 16.0 kHz
HSH G -12 to +12 dB
Sense 0 to 100
Direction UP, DOWN
Decay 44.1kHz: 6.0ms to 46.0s
48kHz: 5.0ms to 42.3s
88.2kHz: 3ms to 23.0s
96kHz: 3ms to 21.1s
Offset 0 to 100
FB.Gain -99 to +99%
Stage 2, 4, 6, 8, 10, 12, 14, 16
LSH F 21.2 Hz to 8.00 kHz
LSH G -12 to +12 dB
HSH F 50.0 Hz to 16.0 kHz
HSH G -12 to +12 dB
Function
Guitar amp simulation type
Distortion type (DST = distortion, OVD = overdrive)
Distortion drive
Master volume
Bass tone control
Middle tone control
High tone control
Speaker cabinet simulation depth
EQ (peaking type) frequency
EQ (peaking type) gain
EQ (peaking type) bandwidth
Noise reduction
Sensitivity
Upward or downward frequency change
Filter frequency change decay speed
Filter type
Filter frequency offset
Filter resonance
Output Level
Sensitivity
Upward or downward frequency change
Decay speed
Delay time offset
Feedback gain (plus values for normal-phase
feedback, minus values for reverse-phase
feedback)
Low shelving filter frequency
Low shelving filter gain
EQ (peaking type) frequency
EQ (peaking type) gain
EQ (peaking type) bandwidth
High shelving filter frequency
High shelving filter gain
Sensitivity
Upward or downward frequency change
Decay speed
Lowest phase-shifted frequency offset
Feedback gain (plus values for normal-phase
feedback, minus values for reverse-phase
feedback)
Number of phase shift stages
Low shelving filter frequency
Low shelving filter gain
High shelving filter frequency
High shelving filter gain