Omron CX-PROGRAMMER V9 - REV 12-2009 Operation Manual page 27

Unit Versions and Programming Devices
Unit Versions and Programming Devices for CJ2 CPU Units
CPU Unit
Functions for unit version
CJ2H-CPU6@-EIP
1.0
Unit version 1.0
Functions added for unit
CJ2H-CPU6@-EIP
version 1.1
Unit version 1.1
Functions added for unit
CJ2H-CPU6@
version 1.1
Unit version 1.1
Functions added for unit
CJ2H-CPU6@-EIP
version 1.2
Unit version 1.2
Functions added for unit
CJ2H-CPU6@
version 1.2
Unit version 1.2
×: Cannot be used, ∆: Can be used except for new functions added for unit versions, ❍: Can be used
Note 1.
2.
3.
Unit Versions and Programming Devices for CPU Units Other Than CJ2 CPU Units
CPU Unit
CS/CJ Series CPU Functions added for unit
Units, Unit Ver. 4.0 version 4.0
CS/CJ Series CPU Functions added for unit
Units, Unit Ver. 3.0 version 3.0
CS/CJ Series CPU Functions added for unit
Units, Unit Ver. 2.0 version 2.0
CS1D CPU Units for Functions added for unit
Single-CPU Systems, version 2.0
Unit Ver. 2.0
CS1D CPU Units for Functions added for unit
Duplex-CPU Systems, version 1.1
Unit Ver.1.1
×: Cannot be used, ∆: Can be used except for new functions added for unit versions, ❍: Can be used
Note 1.
2.
3.
4.
CX-Programmer version 4.0 or higher must be used to enable using the
functions added for CPU Unit Ver. 2.0. The following tables show the
relationship between unit versions and CX-Programmer versions.
Functions
It is not necessary to upgrade the version of the CX-Programmer if functionality that was
enhanced for the upgrade of the CPU Unit will not be used.
CX-Programmer version 8.1 or higher is required to use the functions added for unit
version 1.1. The high-speed interrupt function and changing the minimum cycle time
setting in MONITOR mode, however, are also supported by CX-Programmer version
8.02.
A Programming Console cannot be used with a CJ2H CPU Unit.
Functions
As shown above, there is no need to upgrade to CX-Programmer version 4.0 as long as
the functions added for unit version 2.0 or unit version 1.1 are not used.
CX-Programmer version 7.0 or higher is required to use functions added for unit version
4.0. Additional functions are supported if CX-Programmer version 7.2 or higher is used.
Unit version 4.2 of the CJ1H-CPU6@-R is supported only by CX-Programmer version 8.0
or higher.
CX-Programmer version 8.0 or higher is required to use unit version 4.2 of the CJ1H-
CPU6@-R.
Required Programming Device
Ver. 7.1 or lower Ver. 8.0
❍
×
× ∆
× ∆
×
∆
× ∆
Required Programming Device
Ver. 3.3 Ver. 4.0
∆ ∆
∆ ∆
❍
∆
❍
∆
❍
∆
CX-Programmer
Ver. 8.1 Ver. 8.2
❍ ❍
❍ ❍
❍ ❍
∆ ∆
∆ ∆
CX-Programmer
Ver. 5.0 Ver. 7.0
Ver. 6.0
❍ ❍
∆
❍ ❍ ❍
❍ ❍ ❍
❍ ❍ ❍
❍ ❍ ❍
CX-Programmer_Page (
Ver. 8.3
❍
❍
❍
❍
❍
Ver. 7.2 Ver. 8.0
or later
❍
(See note
4.)
❍
❍
❍
❍
xxiv
)