Hitachi WJ Series User Manual page 446

Chapter 18
Code Name
00: Disable
Overcurrent 01: Enable (without voltage
b027 suppression reduction)
enable 02: Enable (with voltage
reduction)
(0.20 to 2.00) × Rated
Active frequency
current (A) (Normal duty (ND))
b028 matching restart
(0.20 to 1.50) × Rated
level
current (A) (Low duty (LD))
Active frequency
b029 matching restart 0.1 to 3000.0 (s)
constant (speed)
00: Output frequency at shut
Active frequency
b030 matching restart
01: Maximum frequency
speed selection
02: Setting frequency
00: [SFT] terminal (locked
01: [SFT] terminal (locked
Soft-Lock
b031
selection
02: Locked except [b031]
03: Locked except [b031] and
Motor cable
b033 length code 5 to 20
selection
Accum. RUN time
(RNT) / Accum.
b034 0 to 65535 (× 10hr)
power-on time
(ONT)
RUN direction 00: No restriction
b035 restriction 01: Only forward
selection 02: Only reverse
Reduced voltage 0 (short time) to 255 (long
b036
start time time)
00: Full display
Display 01: Function-specific display
b037 restriction 02: User settings and [b037]
selection 03: Data comparison display
05: Monitor only
000: Parameter that SET-key
Initial display 001 to 060: d001 to d060
b038
selection 201: F001
202: Monitor B display of
User-parameter
00: Disable
b039 automatic setting
01: Enable
function enable
00: 4 quadrant individual
Torque limit 01: Switched by terminal
b040
selection
02: [Ai1] terminal input
03: Option
Torque limit 1
b041 0 to 200 (%) / no: Disable
(Forward drive)
Torque limit 2
b042 (Reverse 0 to 200 (%) / no: Disable
regenerative)
Torque limit 3
b043 0 to 200 (%) / no: Disable
(Reverse drive)
Torque limit 4
b044 (Forward 0 to 200 (%) / no: Disable
regenerative)
*1. 100% of the set value means the rated current of the WJ-C1.
*2. The default settings when initialize by setting 00/01/03 to "Initialize data selection [b085]".
List of Parameters/Modbus Coil/Register Numbers
Data range
down
except [b031])
except [b031] and
frequency settings)
frequency settings
was pressed last
WOP
setting
[TRQ1]/[TRQ2]
18-2-13
Change
Initial Set
during
value value Register No.
running
01/
00/ ✓ 131Ch
*2
01
Rated
✓ 131Dh
current
0.50 ✓ 131Eh
00 ✓ 131Fh
01 ✓ 1320h
10 ✓ 1322h
1323h (High)
0 ✓
1324h (Low)
00 × 1325h
2 ✓ 1326h
00 ✓ 1327h
001 ✓ 1328h
00 ✓ 1329h
00 ✓ 132Ah
200 ✓ 132Bh
200 ✓ 132Ch
200 ✓ 132Dh
200 ✓ 132Eh
Modbus communication
Data Range Resolution
0 to 2 -
200 to 2000 (ND) 0.1
200 to 1500 (LD) (%)
1 to 30000 0.1
0 to 2 -
0 to 3
* Writing 10 is
invalid and no -
communication
error.
5 to 20 1
0 to 65535 10hr 9-11-9
0 to 2 -
0 to 255 -
0 to 5
* Writing 4 is
invalid and no -
communication
error.
000 to 202 -
0 to 1 -
0 to 3 -
0 to 200/
1
255(no)
0 to 200/
1
255(no)
0 to 200/
1
255(no)
0 to 200/
1
255(no)
Page
9-9-3
*1
9-7-4
7-2-5
8-1-14
9-4-2
9-7-1
7-2-1
7-2-8
7-2-9
9-6-2
9-6-2