Hitachi WJ Series User Manual page 431

Chapter 18
Coil
Item name
number
002Ch FA5 (Set frequency reached 2)
002Dh OL2 (Overload warning notice 2)
Ai1Dc (Analog [Ai1]
002Eh
disconnection detection)
Ai2Dc (Analog [Ai2]
002Fh
disconnection detection)
0030h (Reserved)
0031h (Reserved)
0032h FBV (PID feedback comparison)
0033h NDc (Communication line disconnection)
0034h LOG1 (Logical operation result 1)
0035h LOG2 (Logical operation result 2)
0036h LOG3 (Logical operation result 3)
0037h (Reserved)
0038h (Reserved)
0039h (Reserved)
003Ah WAC (Capacitor life warning)
003Bh WAF (Cooling-fan life warning)
003Ch FR (RUN command active)
003Dh OHF (Cooling fin overheat warning)
003Eh LOC (Low current signal)
003Fh MO1 (General-purpose output 1)
0040h MO2 (General-purpose output 2)
0041h MO3 (General-purpose output 3)
0042h (Reserved)
0043h (Reserved)
0044h (Reserved)
0045h IRDY (Inverter ready)
0046h FWR (Forward rotation)
0047h RVR (Reverse rotation)
0048h MJA (Major failure)
0049h Data writing in progress
004Ah CRC error *2
*2
004Bh Overrun error
004Ch Framing error *2
*2
004Dh Parity error
004Eh Sum check error
004Fh (Reserved)
0050h WCAi1 (Window comparator [Ai1])
0051h WCAi2 (Window comparator [Ai2])
0052h (Reserved)
0053h (Reserved)
0054h FREF (Frequency reference by keypad)
0055h REF (RUN command by keypad)
0056h SETM (2nd motor selection)
0057h (Reserved)
0058h (Reserved)
0059h
Not used
-
*2. The content of the communication error is retained until an error reset is input (it can be reset during running).
List of Parameters/Modbus Coil/Register Numbers
R/W
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
- -
- -
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
- -
- -
- -
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
- -
- -
- -
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: ON / 0: OFF
R 1: Writing in progress / 0: Normal state
R 1: With error / 0: No error
R 1: With error / 0: No error
R 1: With error / 0: No error
R 1: With error / 0: No error
*2 R 1: With error / 0: No error
- -
R 1: ON / 0: OFF
R 1: ON / 0: OFF
- -
- -
R 1: Keypad / 0: Other than keypad
R 1: Keypad / 0: Other than keypad
R 1: 2nd control selected / 0: 1st control selected
- -
- -
- Not accessible
18-1-2
Setting