Table of Contents
Advertisement
1.3.4 List of Cables
Type
Motor side PLG cable
CNP2E-1-xM
Spindle side accuracy detector
TS5690 cable
Spindle side detector cable
CNP3EZ-2P-xM
OSE-1024 cable
Spindle side detector cable
CNP3EZ-3P-xM
OSE-1024 cable
For HF-KP (Servo) Motor side detector relay cable (motor side)
CNV22J-K1P-0.3M
Lead out in direction of motor shaft
Compatible with only IP65
For HF-KP (Servo) Motor side detector relay cable (motor side)
CNV22J-K2P-0.3M
Lead out in opposite direction of motor shaft
Compatible with only IP65
Motor side detector cable (for A51/A74N(/A74)) /
CNV2E-6P-xM
Ball screw side detector cable
Motor side detector cable (for A51/A74N(/A74)) /
CNV2E-7P-xM
Ball screw side detector cable
For HF/HF-H, HF-KP (Tool spindle) Motor side detector cable (for A48/
CNV2E-8P-xM
A51/A74N(/A74)) /
For HF-KP (Servo) Motor side detector relay cable (Drive unit side)
For HF/HF-H, HF-KP (Tool spindle) Motor side detector cable (for A48/
CNV2E-9P-xM
A51/A74N(/A74))
CNV2E-D-xM
MDS-B-SD unit cable
CNV2E-HP-xM
MDS-B-HR unit cable
For HF-KP (Servo) Motor side detector cable
CNV2E-K1P-xM
Lead out in direction of motor shaft
Compatible with only IP65
For HF-KP (Servo) Motor side detector cable
CNV2E-K2P-xM
Lead out in opposite direction of motor shaft
Compatible with only IP65
Battery cable
DG21-xM
(For drive unit - battery unit)
Battery cable
(For drive unit - drive unit)
DG22-xM
(Note) This cable is required to supply the power from the battery unit to
multiple drive units.
Battery cable
(For drive unit - battery box)
DG23-xM
(Note) The battery box side is connected using a bare conductor or a
terminal bar.
5V supply / DO output cable
(For drive unit - battery box)
DG24-xM
(Note) The battery box side is connected using a bare conductor or a
terminal bar.
Manual pulse generator cable (5V): 1ch
F023 LxM
(for connection to operation panel I/O unit)
Manual pulse generator cable (5V): 2ch
F024 LxM
(for connection to operation panel I/O unit)
F034 LxM
RS-232C I/F cable: 1ch (for control unit)
F035 LxM
RS-232C I/F cable: 2ch (for control unit)
F070 LxM
24VDC power cable
F110 LxM
24VDC power cable for PD25/PD27
F120 LxM
Emergency stop cable
F170 LxM
ON/OFF switch cable for PD25/PD27
F221 LxM
Analog output cable
Manual pulse generator cable (12V): 1ch
F320 LxM
(for connection to operation panel I/O unit)
Manual pulse generator cable (12V): 2ch
F321 LxM
(for connection to operation panel I/O unit)
DI/DO cable (one side connector)
F351
(for operation panel I/O unit)
FCUA-R030-xM
SKIP input cable
FCUA-R031-xM
Analog input/output cable (for remote I/O unit)
FCUA-R050-xM
Synchronous encoder - control unit (straight, with connector)
FCUA-R054-xM
Synchronous encoder - control unit (right angle, with connector)
Application
M70V Series Connection Manual
1.3 List of Configuration
Length (m) of cables provided
by Mitsubishi
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
0.3
0.3
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
2, 3, 4, 5, 7, 10, 15, 20, 25, 30
2, 3, 5, 7, 10
2, 3, 5, 7, 10
0.3, 0.5, 1, 5
0.3, 0.5, 1, 2, 3, 5, 7, 10
0.3, 0.5, 1, 2, 3, 5, 7, 10
0.3, 0.5, 1, 2, 3, 5, 7, 10
1, 2, 3, 5, 8, 10, 15, 20
1, 2, 3, 5, 8, 10, 15, 20
0.5, 1, 2, 3, 5, 8, 10
0.5, 1, 2, 3, 5, 8, 10
0.5, 1.5, 3, 5, 8, 10, 15, 20
0.5, 1.5, 3, 5, 8, 10, 15
0.5, 1.5, 3, 5, 8, 10, 15, 20
0.5, 1.5, 3, 5, 8, 10, 15
1, 2, 3, 5, 8, 10, 15, 20
1, 2, 3, 5, 8, 10, 15, 20
1, 2, 3, 5, 8, 10, 15, 20
3
3, 7
2, 3, 7
5
3, 5, 10, 15, 20
Max. cable
length
30m
30m
30m
0.3m
0.3m
30m
30m
30m
30m
30m
30m
10m
10m
5m
10m
10m
10m
20m
20m
15m (*)
15m (*)
30m
15m
30m
15m
30m
50m
50m
50m
20m
30m
30m
30m
9
Advertisement
Table of Contents
