Table of Contents
Advertisement
f The following items can be selected only when [SLOT BUTTON] is selected in [INPUT SELECT BUTTON].
g The items from [SDI1 [SLOT]] to [SDI4 [SLOT]] can be selected when the optional Interface Board for
12G-SDI (Model No.: ET-MDN12G10) is installed in the slot.
g [HDMI1 [SLOT]] and [HDMI2 [SLOT]] can be selected when the optional Interface Board for HDMI 2 input
(Model No.: ET-MDNHM10) is installed in the slot.
g [DVI-D1 [SLOT]] and [DVI-D2 [SLOT]] can be selected when the optional Interface Board for DVI-D 2
input (Model No.: ET-MDNDV10) is installed in the slot.
g [DisplayPort1 [SLOT]] and [DisplayPort2 [SLOT]] can be selected when the optional Interface Board for
DisplayPort 2 input (Model No.: ET-MDNDP10) is installed in the slot.
[TOGGLE]
[SDI1 [SLOT]]
[SDI2 [SLOT]]
[SDI3 [SLOT]]
[SDI4 [SLOT]]
[HDMI1 [SLOT]]
[HDMI2 [SLOT]]
[DVI-D1 [SLOT]]
[DVI-D2 [SLOT]]
[DisplayPort1 [SLOT]]
[DisplayPort2 [SLOT]]
[DISABLE]
f When [INPUT SELECT BUTTON] is selected in Step 7), once the switching of the item is completed, press
the <MENU> button. The screen returns to the [CONTROL PANEL] screen or the [REMOTE CONTROL]
screen.
9)
Press as to select [APPLY], and press the <ENTER> button.
f The confirmation screen is displayed.
10) Press qw to select [OK], and press the <ENTER> button.
Note
f When a button operation is performed on the device set to [DISABLE], the [CONTROL DEVICE PASSWORD] screen is displayed.
Enter the control device password.
f The [CONTROL DEVICE PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.
f If the operations of both [CONTROL PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot
enter standby).
f When the setting has completed, the menu screen will disappear. To operate continuously, press the <MENU> button to display the main
menu.
f Even when button operations on the remote control are disabled, the operation of the <ID SET> button on the remote control is enabled.
[CONTROL DEVICE PASSWORD CHANGE]
The control device password can be changed.
1)
Press as to select [CONTROL DEVICE PASSWORD CHANGE].
2)
Press the <ENTER> button.
f The [CONTROL DEVICE PASSWORD CHANGE] screen is displayed.
3)
Press asqw to select the text, and press the <ENTER> button to enter the text.
4)
Press asqw to select [OK], and press the <ENTER> button.
f To cancel, select [CANCEL].
Attention
f The initial password is "AAAA" by the factory default setting, or after initialized by one of the following methods.
g When initialized by selecting the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET]
g When initialized by setting the [PROJECTOR SETUP] menu → [INITIALIZE] → [USER SETTINGS] → [OTHER USER SETTING] to
[INITIALIZE]
f Change the password periodically that is hard to guess.
f To initialize your password, consult your distributor.
Chapter 4 Settings — [SECURITY] menu
Switches the input of the Interface Board installed in the slot in turn when the button is operated.
Fixes to selection operation of the SDI1 input of the Interface Board.
Fixes to selection operation of the SDI2 input of the Interface Board.
Fixes to selection operation of the SDI3 input of the Interface Board.
Fixes to selection operation of the SDI4 input of the Interface Board.
Fixes to selection operation of the HDMI1 input of the Interface Board.
Fixes to selection operation of the HDMI2 input of the Interface Board.
Fixes to selection operation of the DVI-D1 input of the Interface Board.
Fixes to selection operation of the DVI-D2 input of the Interface Board.
Fixes to selection operation of the DisplayPort1 input of the Interface Board.
Fixes to selection operation of the DisplayPort2 input of the Interface Board.
Disables button operations.
ENGLISH - 175
Advertisement
Table of Contents
