Table of Contents
Advertisement
10) Press as to select a [COMMAND].
f For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time
you press qw.
f When [INPUT] is selected, press the <ENTER> button, and then press asqw to select the input to be
set.
[COMMAND]
[POWER ON]
[STANDBY]
[QUICK STARTUP]
[SHUTTER]
[INPUT]
[OPERATING MODE]
*1 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
*2 This can be selected when the optional Interface Board equipped with corresponding input is installed in the slot.
*3 If you change the settings while using the projector, the duration until the luminance decreases by half may shorten or the luminance may
decrease.
*4 Only for PT-RCQ80
*5 Only for PT-RCQ10
11) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 156)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
158 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
―
―
[ON]
[OFF]
[OPEN]
[CLOSE]
[HDMI]
[DVI-D]
[SDI]
[DIGITAL LINK]
[INPUT1] - [INPUT10]
[HDMI1 [SLOT]]
[HDMI2 [SLOT]]
[DVI-D1 [SLOT]]
[DVI-D2 [SLOT]]
[SDI1 [SLOT]]
*2
[SDI2 [SLOT]]
*2
[SDI3 [SLOT]]
*2
[SDI4 [SLOT]]
*2
[DisplayPort1 [SLOT]]
[DisplayPort2 [SLOT]]
[NORMAL]
[ECO]
[QUIET]
*4
[QUIET1]
*5
*3
[QUIET2]
*5
[USER1]
[USER2]
[USER3]
Switches on the projector.
Enters standby.
Enables the function of the [PROJECTOR SETUP] menu →
[QUICK STARTUP].
Disables the function of the [PROJECTOR SETUP] menu →
[QUICK STARTUP].
Disables the shutter function (shutter: opened).
Enables the shutter function (shutter: closed).
Switches the input to HDMI.
Switches the input to DVI-D.
Switches the input to SDI.
Switches the input to DIGITAL LINK.
Switches the input to DIGITAL LINK, and switches the input of the
*1
Panasonic twisted-pair-cable transmitter to the specified input.
Switches the input to HDMI1 of the Interface Board.
*2
Switches the input to HDMI2 of the Interface Board.
*2
Switches the input to DVI-D1 of the Interface Board.
*2
Switches the input to DVI-D2 of the Interface Board.
*2
Switches the input to SDI1 of the Interface Board.
Switches the input to SDI2 of the Interface Board.
Switches the input to SDI3 of the Interface Board.
Switches the input to SDI4 of the Interface Board.
Switches the input to DisplayPort1 of the Interface Board.
*2
Switches the input to DisplayPort2 of the Interface Board.
*2
Prioritizes brightness.
Controls the power to increase the life of the light source although
the brightness decreases compared to [NORMAL].
Operates the projector with low noise although the brightness
decreases compared to [NORMAL].
Operates the projector with even lower noise although the
brightness decreases compared to [QUIET1].
Controls the power with the setting set in [USER1].
Controls the power with the setting set in [USER2].
Controls the power with the setting set in [USER3].
Description
Advertisement
Table of Contents
