Grizzly G0853 Owner's Manual page 26

Inventory (Figure 15)
Z. Arbor Locking Pin ....................................... 1
AA. Miter Fence Clamp ..................................... 1
AB. Crosscut Fence Flip Stops ......................... 2
AC. Toolbox ....................................................... 1
AD. Crosscut Fence Ext. Clamp Assembly ....... 1
AE. Rip Fence Slide Lock Handle ..................... 1
AF. Crosscut Fence Pivot Lock Knob ............... 1
AG. Crosscut Fence Angle Scale Lock Knob ... 1
AH. Push Handle ............................................... 1
AI. Edge Shoe Assembly ................................. 1
AJ. Push Stick .................................................. 1
AK. Dust Hose 3" x 16
AL. Hold-Down Assembly ................................. 1
AM. Miter Fence Bracket ................................... 1
AN. Dust Port 4" ................................................ 1
AO. Knob Bolt M8-1.25 x 50 ............................. 1
AP. Dust Port 3" ................................................ 1
AQ. Miter Gauge ................................................ 1
AR. Riving Knife ................................................ 1
AS. Hose Clamps 3
⁄ " ...................................... 2
1
4
AT. T-Bolt M8-1.25 x 35 .................................... 1
AU. T-Slot Plate M8-1.25 ................................... 1
AV. L-Bracket .................................................... 1
AW. Miter Fence Flip Stop ................................ 1
AB
AA
Z
AD AE AF
AJ AK
AM AN
AR AS
Figure 15. G0853 Inventory 3.
-24-
Qty
⁄ " .................................. 1
1
2
AC
AG AH AI
AL
AO AP AQ
AT AU AV AW
Component Hardware (not shown)
Hex Bolts M12-1.75 x 50 (Sliding Table) ............ 5
Lock Washers 12mm (Sliding Table) ................. 5
Spacers 12mm (Sliding Table) ........................... 5
Set Screws M10-1.5 x 20 (Ext. Tables) .............. 6
Hex Nuts M10-1.5 (Ext. Tables) ......................... 6
Cap Screws M12-1.75 x 30 (Rip Fence) ............ 2
Lock Washers 12mm (Rip Fence) ..................... 2
Plastic Caps 22mm (Rip Fence) ........................ 2
Plastic Cap 16mm (Rip Fence) .......................... 1
Fender Washers 8mm (Crosscut Table Brace) ... 2
T-Nut M8-1.25 (Crosscut Table Brace) .............. 1
Hex Bolt M12-1.75 x 75 (Lower Guard Arm) ...... 1
Hex Nut M12-1.75 (Lower Guard Arm) ............... 1
Cap Screws M8-1.25 x 25 (Guard Arm Post) ... 4
Flat Washers 8mm (Guard Arm Post) ............... 4
Lock Washers 8mm (Guard Arm Post) ............. 4
Cap Screws M6-1 x 20 (Blade Guard Cover) .... 3
Flat Washers 6mm (Blade Guard Cover) .......... 3
Lock Washers 6mm (Blade Guard Cover) ........ 3
Steel Tab (Control Panel Arm) ........................... 1
BH Cap Screws M6-1 x 12 (3" Dust Port) ......... 2
Lock Washers 6mm (3" Dust Port) .................... 2
Cap Screws M5-.8 x 16 (Control Panel) ............ 4
Flat Washers 5mm (Control Panel) ................... 4
Lock Washers 5mm (Control Panel) ................. 4
Cap Screws M6-1 x 20 (Large Ext. Table) ........ 2
Flat Washers 6mm (Large Ext. Table) ............... 3
Lock Washers 6mm (Large Ext. Table) ............. 2
Hex Nut M6-1 (Large Ext. Table) ....................... 1
Spacer (Hold-Down & Miter Gauge) .................. 1
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Model G0853 (Mfd. Since 07/18)
Qty