Korg Krome Parameter Manual page 363

(1):When a arpeggiator controller is assigned to a CC#
indicated by [*] (Global P2: Controllers– MIDI CC#
Assign)
*: Assignable
[*]:The ARP Controllers can be assigned to CC#00–119.
CC#s indicated by [*] will be assigned automatically
when you execute the Global P2– MIDI CC# Assign
menu command Reset Controller MIDI Assign with the
CC Default setting.
The CC Default settings are the CC#s recommended as
the CC# for each of these controllers. Normally you
should use these settings when assigning CC#s.
When one of the KROME's controllers is operated, the
corresponding or the assigned control change will be
transmitted.
If you choose USER [1] –USER [4], or SW1/2, its MIDI
control change message will be transmitted according to the
settings in Realtime Controls Knob Assign, SW1/2 Assign.
If you've selected ARP ON/OFF, ARP GATE, ARP
VELOCITY, ARP SWING, ARP STEP, those MIDI control
change messages will be transmitted according to the Global
P2‐MIDI CC# Assign settings.
The following sections describes operation in each mode.
Program mode
When one of the KROME's controllers is operated, a control
change message will be transmitted on the global MIDI
channel (MIDI Channel Global 1–1a).
If the Realtime Controls is set to USER, and knobs 1–4
or the assignable pedal are assigned to Master Volume,
the universal exclusive message Master Volume will be
transmitted.
Combination mode
When one of the KROME's controllers is operated, a control
change message will be transmitted on the global MIDI
channel (MIDI Channel Global 1–1a).
Simultaneously, the message will also be transmitted on the
MIDI channel (MIDI Channel Combi 3–1(2)c) of any timbre
whose Status (Combi 3–1(2)c) is EXT or EX2.
When one of the KROME's controllers is operated, its effect
will apply to any timbre whose Status is INT and whose
MIDI Channel setting is either Gch or the same as the
global MIDI channel.
In the case of Master Volume, the universal exclusive
message Master Volume will be transmitted only on the
global MIDI channel.
You can make settings for MIDI Filter (Combi P5) to
enable or disable control changes and controllers for
each timbre. When checked, the above operations will
be enabled.
Effect dynamic modulation can be controlled when the Ch
(Combi 8–4a, 9–2a) setting for IFX1–5, MFX1, 2, or TFX is
either set to Gch or to the same channel as the global MIDI
channel. (In the case of All Routed, control is possible on the
MIDI channel of any routed timbre.)
Sequencer mode
When one of the KROME's controllers is operated, its effect
will apply to the MIDI track 1–16 that is currently selected
by Track Select (Seq 0–1(2)a).
If the Status (Seq 3–1(2)c) of the track selected by Track
Select is EXT, EX2, or BTH, a control change message will be
MIDI transmission when the KROME's controllers are operated
transmitted on the MIDI channel specified by MIDI
Channel (Seq 3–1(2)c).
If the Status is INT or BTH, operating one of the KROME's
controllers will affect only that MIDI track. Simultaneously,
the same effect will also apply to any MIDI track with the
same MIDI Channel setting.
In the case of Master Volume, the universal exclusive
message Master Volume will be transmitted.
You can make settings for MIDI Filter (Seq P3) to enable
or disable control changes and controllers for each
track. When checked, the operations effective for a
Status of INT or BTH will be enabled. Tracks whose
Status is EXT, EX2, or BTH will transmit control
changes regardless of this setting.
Effect dynamic modulation can be controlled when the Ch
(Seq 8–4a, 9–2a) setting for IFX1–5, MFX1, 2, or TFX matches
the MIDI channel of the track selected by Track Select. (In
the case of All Routed, control is possible on the MIDI
channel of all routed tracks.)
If one of the KROME's controllers is operated during
realtime recording, the corresponding or assigned control
change will be recorded.
355