072: St. Dynamic Delay (Stereo Dynamic Delay) - Korg Krome Parameter Manual

–Wet... Sets the balance between the
Wet/Dry –1 : 99, Dry, effect and the dry input
1 : 99...Wet
l Selects a modulation source for
Src Off...Tempo
Wet/Dry
Sets the modulation amount for
Amt –100...+100
Wet/Dry
b: D-mod Modulation
When the modulation source is used for control, this
parameter reverses the left and right modulation direction.
d: LFO D-mod Sync
d: Src
h: L LFO Phase [deg]
i: R LFO Phase [deg]
If LFO D-mod Sync is On, the LFO will be reset by the
modulation source that is received.
The Src parameter sets the modulation source that resets the
LFO. For example, you can assign Gate as a modulation
source so that the sweep always starts from the specified
point.
L LFO Phase and R LFO Phase set the phase obtained when
the left and right LFOs are reset. In this way, you can create
changes in pitch sweep for the left and right channels
individually.
The effect is off when a value of the modulation source
specified in the Src parameter is 63 or smaller, and the
effect is on when the value is 64 or higher. The LFO is
triggered and reset to the L LFO Phase and R LFO
Phase settings when the value changes from 63 or
smaller to 64 or higher.
Delay 072: St. Dynamic Delay (Stereo Dynamic Delay)
072: St. Dynamic Delay (Stereo
p.259
Dynamic Delay)
This stereo delay controls the level of delay according to the
input signal level. You can use this as a ducking delay that
applies delay to the sound only when you play keys at a
high velocity or only when the volume level is low.
Stereo In - Stereo Out
Left
Right
Control
Target
a
Polarity
Threshold
b
Offset
c Attack
d Release
L Delay Time
e
[msec]
R Delay Time
f
[msec]
g Feedback
High Damp
[%]
h
Low Damp
[%]
i Spread
Wet/Dry
j
Src
Amt
a: Control Target
This parameter selects no level control, delay output control
(effect balance), or feedback amount control.
a: Polarity
b: Threshold
b: Offset
c: Attack
d: Release
The Offset parameter specifies the value for the Control
Target parameter (that is set to None), expressed as the ratio
relative to the parameter value (the Wet/Dry value with
Control Target = Output Level, or the Feedback value with
Control Target = Feedback).
When Polarity is positive, the Control Target value is
obtained by multiplying the parameter value by the Offset
value (if the input level is below the threshold), or equals the
parameter value if the input level exceeds the threshold.
When Polarity is negative, Control Target value equals the
parameter value if the input level is below the threshold, or
is obtained by multiplying the parameter value by the
Offset value if the level exceeds the threshold.
High Damp Low Damp
Delay
Feedback
High Damp Low Damp
Delay
FB
+
Attack, Release
Envelope
Threshold
Selects from no control, output,
None, Out, FB
and feedback
+, – Reverses level control
Sets the level to which the effect
0...100
is applied
Sets the offset of level control
0...100
Sets the attack time of level
1...100
control
Sets the release time of level
1...100
control
Sets the delay time for the left
0.0...1360.0
channel
Sets the delay time for the right
0.0...1360.0
channel
–100...+100 Sets the feedback amount
Sets the damping amount in the
0...100
high range
Sets the damping amount in the
0...100
low range
Sets the width of the stereo
–100...+100 image of the effect sound
Dry,
Sets the balance between the
1 : 99...99 : 1,
effect and the dry input
Wet
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount for
–100...+100
Wet/Dry
Wet / Dry
Spread
Wet / Dry
Out
Control Target
p.291
p.291
p.291
p.291
p.291
p.291
p.289
p.289
p.289
291