9-3: Mfx2, 9-4: Tfx; 9-5: Common Fx Lfo - Korg Krome Parameter Manual

Combination mode
The same presets appear in all of the modes (Program,
Combination, Sequence).
Note that edits to effects parameters are automatically
stored with the Combination you don't need to store them as
an Effect Preset. Presets just make it easier to re‐use your
favorite settings.
For instance, you can save an Effect Preset while working on
a particular Combination, and then later use the same Effect
Preset in a different Program, Combination, or Song.
P00: Initial Set: These are the default settings that are
recalled when you select an effect type in the P9: MFX/TFX/
LFO– Routing page. You can't save your own settings here.
P01...P15: Preset data is saved in this area. We recommend
that you store your settings in U00–U15.
U00...U15: These are areas in which you can store your own
settings.
---------------: This shows that no Effect Preset has been
selected. You'll see this if you've just selected an effect,
written a Combination, or selected a new Combination.
Selecting this setting from the menu will not have any effect.
Note: Combinations save the effects parameter settings, but
they don't save the number of the selected Effect Preset. If
you select an Effect Preset, and then save the Combination,
the Effect Preset setting will revert to "--------------."
For more details, please see "Using Effect Presets" on
page 60.
MFX1 Parameters
Here, you can set the effect parameters of the insert effect
you chose in the P9: MFX/TFX/LFO– Routing page.
For details on the master effects, please see the "Effect
Guide" on page 235.
9–2: Menu Command
V
• 0: Write Combination
• 1: Exclusive Solo
• 2: Auto Setup Song
• 3: Copy MFX/TFX
• 4: Swap MFX/TFX
• 5: Write FX Preset
For more information, please see "Combination: Menu
Command" on page 101.
9–3: MFX2, 9–4: TFX
These pages let you edit the parameters of Master Effect 2
and the Total Effect. To select different effects types, use the
P9: MFX/TFX/LFO– Routing page.
The parameters for MFX2, TFX is the same as for MFX1. For
more information, please see "9–2: MFX1" above.
100
see p. 101
see p. 64
see p. 101
see p. 67
see p. 67
see p. 104
9–5: Common FX LFO
9–5a
9–5b
The two Common FX LFOs allow you to synchronize LFO‐
based modulation for multiple effects, such as phasers,
flangers, filters, and so on.
The Common LFOs control only the frequency, MIDI
synchronization, and reset options; each individual effect
still has its own settings for the LFO waveform and phase.
Within the individual effects, you can choose whether to use
one of the Common LFOs, or to use the individual effect's
frequency, sync, and/or reset settings instead. This is done
via the effect's LFO Type parameter; select Individual to use
the effect's settings, or Common 1 or 2 to use the Common
LFOs.
9–5a: Common FX LFO1
Ctrl Ch (Control Channel)
Specifies the MIDI channel that will control dynamic
modulation (Dmod) for Common LFO 1 and 2.
G ch: The global MIDI channel (Global 1–1a) will be used
for control. This is the default.
Sync (Reset)
Source (Dmod Source)
Frequency
MIDI/Tempo Sync
BPM
Base Note
Times
These parameters are the same as in Program mode. For
more information, please see "9–5: Common FX LFO" on
page 100.
9–5b: Common FX LFO2
These parameters are the same as for Common FX LFO1.
9–5: Menu Command
V
• 0: Write Combination see p. 101
• 1: Exclusive Solo see p. 64
• 2: Auto Setup Song see p. 101
• 3: Copy Insert Effect see p. 66
• 4: Swap Insert Effect see p. 67
For more information, please see "Combination: Menu
Command" on page 101.
9–5
Menu
[Ch01...Ch16, G ch]
[Off, On]
[List of Dmod Sources]
[0.02...20.00 (Hz)]
[Off, On]
[MIDI, 40.00...300.00]
3 3 3 3
[ , , , , , , , , , ]
[01...32]