019: St. Analog Record (Stereo Analog Record) - Korg Krome Parameter Manual

Individual,
LFO Type Common1,
Common2
e
Common
LFO Offset –180...+180
[deg]
Depth 0...100
Src Off...Tempo
f
Amt –100...+100
g Resolution 4...24
Output Level 0...100
Src Off...Tempo
h
Amt –100...+100
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
i
Src Off...Tempo
Amt –100...+100
a: Pre LPF
If a sampler with a very low sampling frequency receives
very high‐pitched sound that could not be heard during
playback, it could generate pitch noise that is unrelated to
the original sound. Set Pre LPF to On to prevent this noise
from being generated.
If you set the Sampling Frequency to about 3 kHz and set
Pre LPF to Off, you can create a sound like a ring modulator.
g: Resolution
h: Output Level
If you set a smaller value for the Resolution parameter, the
sound may be distorted. The volume level may also be
changed. Use Output Level to adjust the level.
262
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Sets the phase offset when Type
= Common 1 or Common 2
p.257
Sets the depth of the sampling
frequency LFO modulation
Selects the LFO modulation
source of the sampling
frequency
Sets the LFO modulation
amount of the sampling
frequency
Sets the data bit length p.262
Sets the output level p.262
Selects the modulation source
for the output level
Sets the modulation amount of
the output level
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount for
Wet/Dry
019: St. Analog Record (Stereo
Analog Record)
This effect simulates the noise caused by scratches and dust
on analog records. It also reproduces some of the
modulation caused by a warped turntable.
Stereo In - Stereo Out
Left
EQ Trim Pre EQ
EQ Trim
Pre EQ
Right
a Speed [RPM] 33 1/3, 45, 78 Sets the r.p.m. of a record
Sets the modulation depth
b Flutter
0...100
Noise Density 0...100 Sets the noise density
c
Noise Tone 0...100 Sets the noise tone
Noise Level 0...100 Sets the noise level
Selects the modulation source
Src Off...Tempo
d for the noise level
Sets the modulation amount of
Amt –100...+100
the noise level
Sets the click noise level
Click Level 0...100
Selects the modulation source
e Src Off...Tempo
for the click noise level
Sets the modulation amount of
Amt –100...+100
the click noise level
f EQ Trim 0...100 Sets the EQ input level
Pre EQ Cutoff
300...10.00k Sets the EQ center frequency
[Hz]
g
Q 0.5...10.0 Sets the EQ band width
Gain [dB] –18.0...+18.0 Sets the EQ gain
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
h Src Off...Tempo
Wet/Dry
Sets the modulation amount for
Amt –100...+100
Wet/Dry
b: Flutter
This parameter enables you to set the depth of the
modulation caused by a warped turntable.
e: Click Level
This parameter enables you to set the level of the click noise
that occurs once every rotation of the turntable. This
simulation reproduces record noise, and the noise generated
after the music on a vinyl record finishes.
Wet / Dry
Analog Record
Simulation
Wet / Dry
p.262
p.262