070: St. Multitap Delay (Stereo Multitap Delay); 071: St. Mod Delay (Stereo Modulation Delay) - Korg Krome Parameter Manual

070: St. Multitap Delay (Stereo
Multitap Delay)
The left and right Multitap Delays have two taps
respectively. Changing the routing of feedback and tap
output allows you to create various patterns of complex
effect sounds.
Stereo In - Stereo Out
Left
Input Level D-mod
High Damp Low Damp
Mode
High Damp Low Damp
Input Level D-mod
Right
Normal, Cross
Feedback,
a Mode
Cross Pan1,
Cross Pan2
Tap1 Time
b
0.0...1360.0
[msec]
Tap2 Time
c 0.0...1360.0
[msec]
d Tap1 Level 0...100
Feedback
–100...+100
(Tap2)
e Src Off...Tempo
Amt –100...+100
High Damp
f 0...100
[%]
Low Damp
g
0...100
[%]
Input Level
–100...+100
D-mod [%]
h
Src Off...Tempo
Spread –100...+100
i Src Off...Tempo
Amt –100...+100
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
j Src Off...Tempo
Amt –100...+100
Mode: Normal Mode: Cross Feedback
a: Mode
You can change how the left and right delay signals are
panned by modifying the routing of the left and right delay
as shown in the figure above. You need to input different
sounds to each channel in order for this parameter to be
effective.
d: Tap1 Level
This parameter sets the output level of Tap1. Setting a
different level from Tap2 will add a unique touch to a
monotonous delay and feedback.
290
Wet / Dry
Feedback
Delay
(2)
(1)
Tap1=(1)
Mode Spread
Tap1 Level
Tap2=(2)
(1)
(2)
Delay
Feedback
Wet / Dry
Switches the left and right delay
routing p.290
Sets the Tap1 delay time
Sets the Tap2 delay time
Sets the Tap1 output level
p.290
Sets the Tap2 feedback amount
Selects the modulation source of
the Tap2 feedback amount
Sets the modulation amount of
the Tap2 feedback amount
Sets the damping amount in the
high range p.289
Sets the damping amount in the
low range p.289
Sets the modulation amount of
the input level p.284
Selects the modulation source
for the input level p.284
Sets the width of the stereo
image of the effect sound
p.289
Selects the modulation source of
the effect sound's stereo image
width
Sets the modulation amount of
the effect sound's stereo image
width
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount for
Wet/Dry
Mode: Cross Pan1 Mode: Cross Pan2
071: St. Mod Delay (Stereo
Modulation Delay)
This stereo delay uses an LFO to sweep the delay time. The
pitch also varies, creating a delay sound which swells and
shimmers. You can also control the delay time using a
modulation source.
Stereo In - Stereo Out
Left
Delay
Feedback
Delay
Right
D -mod
Response L/R: +/+ +/–
LFO: Tri / Sine LFO Shape
LFO Sync
Switches between LFO
Modulation
a LFO, D-mod modulation control and
Mode
modulation source control
D-mod L/R:+/+, Reversed L/R control by
Modulation L/R:+/– modulation source
Selects the modulation source
b Src Off...Tempo
that controls delay time
Sets the rate of response to the
Response 0...30
modulation source
LFO
Triangle, Sine Selects the LFO Waveform
Waveform
c
Changes the curvature of the
LFO Shape –100...+100
LFO Waveform
LFO D-mod Switches LFO reset off/on
Off, On
Sync
d
Selects the modulation source
Src Off...Tempo
that resets the LFO
LFO
e Frequency 0.02...20.00 Sets the speed of the LFO p.259
[Hz]
When this is on, the LFO speed is
set by BPM, Base Note, and
MIDI Sync Off, On
Times, instead of Frequency
MIDI, MIDI syncs to the system tempo;
BPM 40.00... 40–300 sets the tempo manually
f
300.00 for this individual effect
Selects the type of notes that
Base Note ...
specify the LFO speed
Sets the number of notes that
Times x1...x32
specify the LFO speed
Individual, Selects either (individual) LFO,
LFO Type Common1, Common FX LFO1, or Common
Common2 LFO2
g
Common Sets the phase offset when Type
LFO Offset –180...+180 = Common 1 or Common 2
[deg] p.257
L LFO Phase Sets the phase obtained when
–180...+180
[deg] the left LFO is reset
h
Sets the depth of the left LFO
L Depth 0...200
modulation
R LFO Phase Sets the phase obtained when
–180...+180
[deg] the right LFO is reset
i
Sets the depth of the right LFO
R Depth 0...200
modulation
L Delay Time Sets the delay time for the left
0.0...1000.0
[msec] channel
j
Sets the feedback amount of left
L Feedback –100...+100
delay
R Delay Time Sets the delay time for the right
0.0...1000.0
[msec] channel
k
Sets the feedback amount of
R Feedback –100...+100
right delay
Wet / Dry
Wet / Dry
D-mod
LFO
LFO Phase Modulation Mode
p.291
p.258
p.291
p.257
p.257
p.257
p.257
p.257
p.291
p.291