Mixer - Korg Krome Parameter Manual

Mixer

In Program, Combination, and Sequencer modes, the P8–
Insert FX Setup page lets you set the Pan: CC#8 (post‐IFX
panning), Bus Sel. (Bus Select), Ctrl Bus (FX control bus),
and the Send1 and Send2 levels to the master effects.
If you have checked the Chain to connect the Insert Effects
in series, these parameters Pan: CC#8 – Send2 for the post‐
IFX (last Insert Effect in the chain) signal become effective.
Pan: CC#8
This parameter enables you to set the pan of the post‐IFX
signal.
If you are using the stereo‐in/stereo‐out Insert Effects, set
this parameter to "C064" to enable the Pan settings for the
oscillators (Prog 4–1c, 4–5), timbres (Combi 0–3(4)b), tracks
(Seq 0–3(4)b).
If you are using mono‐in/stereo–out or mono‐in/mono–out
Insert Effects, the Pan settings for the oscillators, timbres,
and tracks are ignored, and they are set to Center. Use the
Pan: CC#8 parameter (Prog 8–2a, Combi/Seq 8–3b) to set the
pan. "L000" is hard left, and "R127" is hard right.
• For more about effect types such as stereo‐in/stereo‐out,
see "In/Out" on page 240.
You can control these parameters via CC#8.
Bus Sel. (Bus Select)
This parameter enables you to specify the destination bus
for the post‐IFX signals.
L/R is a common setting to send signals to the Total Effect
(TFX) before they are routed to the AUDIO OUTPUT L/
MONO and R outputs.
If set to Off, the signal will not be sent to the L/R bus.
Choose this setting if you want to use the Send1 or Send2
levels to route the signal through a master effect in series
(i.e., not as a send effect).
Insert Effect = Stereo In – Stereo Out
OSC1
OSC2
OSC1: Amp1 Pan = L001
Left Center Right
OSC2: Amp2 Pan = R127
Post IFX Pan: CC#8
C064
L032
L001
R096
R127
Left Center
Right
FX Ctrl (FX Control Bus)
This specifies the FX Control bus that follows the insert
effect. The FX Control buses (FX Control 1, 2) are mono two‐
channel buses.
The KROME provides two (mono two‐channel) effect
control buses, giving you a wide range of ways to control
effects.
FX Control buses can be used with vocoder, limiter, and
gate‐type effects.
For details on the effects that be used with FX Control buses,
see "FX Control Buses" on page 238.
As an example, here's how you can use the FX Control bus
following an insert effect.
Example: Gated Reverb
When using a gate effect with a reverberant sound, using the
reverberant sound to control the gate may not produce the
desired results because the reverb extends the duration of
the sound. Normally, you will use the un‐reverberated
sound to control the gate, as shown in the diagram below.
In this example, we send the sound from the OSC etc. to
IFX1 and process it through an equalizer. IFX1 is sent via
Chain to IFX2 and also sent via Ctrl Bus (FX Control Bus) to
1. The Envelope Source of IFX3: Stereo Gate is set to FX
Control 1. This allows the gat to be triggered by a signal
other than its input (the reverberant sound).
Gated Reverb Example
OSC1&2
Timbre/Track
Send1, Send2
These parameters enable you to set the send level of the
signals routed to Master Effects MFX1 and MFX2. The signal
is sent in stereo to master effects MFX1 and MFX2. This is
valid when Bus (Bus Select) is L/R or Off.
If you are not using any Insert Effects, use Send1 and Send2
of the P8: Routing/IFX– Routing page in Program,
Combination, Sequencer, and Song play modes to set the
Master Effect send level.
Send1 responds to CC#93 and Send2 responds to
CC#91.
OSC1: Amp1 Pan = L032
Left Center Right
OSC2: Amp2 Pan = R096
Post IFX Pan: CC#8
C064
L032
L001
R096
R127
Left Center
Right
Insert Effects (IFX1–IFX5) Mixer
IFX1 Chain to IFX2
Bus Select
: IFX2
: IFX1
008: St.Graphic 084: Reverb Hall
7EQ
FX Control Bus
: 1
(FX Control Bus1)
Insert Effect = Mono In - Stereo Out
Mono In - Mono Out
OSC1
Left Center
Left Center
Chain to IFX3 Bus Select
: IFX3 : L/R
006: Stereo Gate
Envelope Source
: FX Ctrl1
OSC2
OSC1: Amp1 Pan = L001
Right
OSC2: Amp2 Pan = R127
Post IFX Pan: CC#8
C064
L032
L001
R096
R127
Right
243