Mixer - Korg Krome Parameter Manual

Effect Guide
becomes available. If you check this box, Send1 and Send2
levels for each key of the selected Drum kit become effective.
If Bus (IFX/Output) Select (Global 5–5b) is set to L/R or Off
for a drum instrument key, Send1 (to MFX1) and
Send2(toMFX2) (Global 5–5b) become effective.
If Bus (IFX/Output) Select is set to IFX1–5, the post‐IFX1–5
Send1 and Send2 (Prog 8–5a) become effective.
If this is unchecked, Send1 (to MFX1) and Send2 (to MFX2)
(Prog 8–1d), and the post IFX1–5 Send1 and Send2 (Prog 8–
2a) will be valid for all drum instruments, in the same way
as when Oscillator Mode is Single or Double.
Combination and Sequencer modes
Use Send1 (to MFX1) and Send2 (to MFX2) (P8: "Routing"
page) for timbres (Combination) and tracks (Sequencer) to
set the Send1 and 2 levels for each timbre and track. As with
Program mode, if Bus (IFX/Output) Select is set to L/R or
Off, Send1 (to MFX1) and Send2 (to MFX2) become
effective.
The actual levels use these Send1 and 2 level values,
multiplied by the send level values of oscillators 1 and 2 of
the Prog P8: Routing/IFX – Routing page.
Send level
For example if you set the program's OSC1 Send1 (to MFX1)
to 127, Send2 (to MFX2) to 064, OSC2 Send1 (to MFX1) to
064, Send2 (to MFX2) to 127, and the combination's Send1
(to MFX1) to 064 and Send2 (to MFX2) to 127, the actual
send levels of the combination will be as follows.
OSC1 Send1=127 (100%) *064 (50%)=064 (50%)
OSC1 Send2=064 (50%) *127 (100%)=064 (50%)
OSC2 Send1=064 (50%) *064 (50%)=032 (25%)
OSC2 Send2=127 (100%) *127 (100%)=127 (100%)
If IFX1–5 is selected for Bus (IFX/Output) Select, use the
Send1 and Send2 parameters for the post‐IFX signals.
Send1 responds to CC#93, and Send2 responds to
CC#91. If Send1 (to MFX1) and Send2 (MFX2)" for each
timbre/track are effective, the parameter will be
controlled on the MIDI channels set for the
corresponding timbres and tracks. If the Send1 and
Send2 parameters for the post‐IFX1–5 signals are
effective, they can be controlled on the MIDI channels
assigned to IFX1–5.
An example for Combination mode is given below. In the
following diagram, Bus (IFX/Output) Select is set so that
Timbre 1 is routed to IFX1, Timbre 2 to IFX2, Timbres 3 and
4 to IFX3, Timbres 5–16 to L/R.
In this case, use Send1 and Send2 for the post‐IFX1 (001:
Stereo Compressor) signal to set the send level of the Timbre
1 routed to the Master Effect. (In this example they are set to
032 and 127.) In the same way, use Send1 and Send2 for the
post‐IFX2 signal to set the send levels of Timbres 2, and use
the Send1 and Send2 parameters for the post‐IFX3 signal to
set the send levels of Timbres 3 and 4. For Timbres 5–8, the
settings of Send1 (to MFX1) and Send2 (to MFX2) will be
effective (for Timbres 9–16, use the Routing 1 T09–16 page).
246
(At this time, the actual send levels use these Send 1 and 2
values multiplied by the Send1 and 2 settings for Program
oscillators 1 and 2.)
Bus Select "DKit" is valid if you've selected a drum track for
a Timbre (Combination) or Track (Sequencer).
If you select DKit, the Bus (IFX/Output) Select (Global 5–
5b) settings for each key become effective, and each drum
instrument sound will be routed to the corresponding buses.
At this time, the actual send levels use these Send 1 and 2
values, multiplied by the Send1 and 2 settings for each
Drum kit key.
If a drum kit's Bus (IFX/Output) Select is set to L/R or Off,
the levels will be these Send 1 and 2 settings multiplied by
the send levels you specify in Prog P8: Routing/IFX –
Routing page for OSC1 Send1 (to MFX1) and Send2 (to
MFX2) (Prog 8–1d), just as in other cases (Oscillator Mode
Single or Double).
If Bus (IFX/Output) Select is set to IFX1–5, use Send1 and
Send2 for the post‐IFX signal.
In Media mode, effects will use the settings of the mode
in which you previously were.

Mixer

The input levels to the master effects are determined by the
send levels. In the P9: MFX/TFX/LFO– Routing page of each
mode, you can specify the output level and chaining (series
connection) between the two master effects.
2
1. Return1, Return2
These adjust the amount of signal that is returned from the
master effects MFX1 and MFX2 outputs to the L/R bus.
The left‐side value of the Wet/Dry parameter for the MFX1
or 2 effect is the output level of that master effect. (In other
words if Wet/Dry is 25:75, the output level is 75%. It is 100%
if Wet, and 0% if Dry.) The Wet/Dry value multiplied by the
Return1 or Return2 value is sent to the L/R bus and mixed
with the P8 : Routing/IFX – Routing page Bus (IFX/Output)
Select L/R or Insert FX Setup page Bus L/R output.
For example, with MFX1 Wet/Dry set to 50:50 (50%) and
Return1 set to 64 (50%), the resultant effect level will be 25%.
3
4
1