Foot Pedal Assignments - Korg Krome Parameter Manual

Appendices
Program Up
This lets you use the switch to increment the current
Program or Combination number, for hands‐free patch
changes. Note that this is only active while on the Prog P0:
Play or Combi P0: Play pages, respectively.
When you use this control, the KROME will also transmit
the corresponding MIDI Program Change and Bank Select
messages.
Program Down
This decrements the current Program or Combination
number, for hands‐free patch changes. For more
information, please see "Program Up" above.
Value Inc
Operating the foot switch will produce the same operation
as pressing the INC button. For more information, please see
"2–1: Menu Command" on page 202.
Value Dec
Operating the foot switch will produce the same operation
as pressing the DEC button.
Song Start/Stop
The foot switch will control sequencer start/stop.
Simultaneously, a MIDI Start or Stop message will be
transmitted.
Song Punch In/Out
If Seq P0: Preference "Recording Setup" (0–8b) is set to
Manual Punch In, the switch can be used to punch‐in and
punch‐out when recording on the sequencer.
Cue Repeat Control
This is valid if the Repeat setting for each step in Seq P11:
Cue List is set to FS (11–1b). If you press the pedal switch
while a step is repeating, this will be the trigger to proceed
to the next step.
Tap Tempo
This duplicates the function of the front‐panel TAP button,
for setting the system tempo in real‐time.
ARP ON/OFF
The foot switch will turn the arpeggiator on/off.
DRUM TRACK ON/OFF
The foot switch will turn the Drum Track on/off.
JS+Y (CC#01)
The switch will control the effect produced by joystick
movement in the +Y direction (Vertical upward).
JS–Y (CC#02)
The switch will control the effect produced by joystick
movement in the –Y direction (Vertical downward).
Value Slider (CC#18)
You can use this general‐purpose controller as an AMS or
Dmod source. Note that you'll also need to assign
ValueSlider (CC#18) to control the desired parameter within
the Program or Effect.
TONE [1]...TONE [4]
USER [1]...USER [4]
Use the switch to control the effect of knobs 1–4 when the
Realtime Controls is in USER/TONE.
(Foot switch "on" is equivalent to turning the knob to the far
right; foot switch "off" is equivalent to turning the knob to
the far left.)
SW1, 2
The footswitch duplicates the function of the selected front‐
panel switch.
ARP GATE
Use the switch to control the arpeggiator's Gate.
350
(Foot switch "on" is equivalent to turning the knob to the far
right; foot switch "off" is equivalent to turning the knob to
the far left.)
ARP VELOCITY
Use the switch to control the arpeggiator's Velocity.
(Foot switch "on" is equivalent to turning the knob to the far
right; foot switch "off" is equivalent to turning the knob to
the far left.)
ARP LENGTH
Use the switch to control the arpeggiator's Length.
(Foot switch "on" is equivalent to turning the knob to the far
right; foot switch "off" is equivalent to turning the knob to
the far left.)
ARP STEP
Use the switch to control the arpeggiator's Step.
(Foot switch "on" is equivalent to turning the knob to the far
right; foot switch "off" is equivalent to turning the knob to
the far left.)

Foot Pedal Assignments

You can connect a pedal (such as the optional Korg XVP‐10
or EXP‐2) to the rear‐panel ASSIGNABLE PEDAL input,
and then use it to control a wide variety of functions, as
described below.
This setting is made for the entire KROME, on the Global P2:
Controllers– Foot Controllers page.
A note on MIDI CCs
Some of the assignments include MIDI CCs, which are
transmitted whenever the knob is moved. Note that the
MIDI CCs can still be received even if they are not assigned
to a physical controller.
If you select USER [1] –USER [4], the MIDI control change
message specified by the Realtime Controls Knob Assign
settings in each mode will be transmitted.
List of Foot Pedal assignments
Off
This setting disables the pedal.
Master Volume
This controls the overall volume, and transmits the
Universal System Exclusive Master Volume message [F0H,
7FH, nn, 04, 01, vv, mm, F7H]. You can use this to adjust the
volumes of all Tracks or Timbres at the same time, while
preserving their relative balance.
Foot Pedal (CC#04)
You can use this general‐purpose controller as an AMS or
Dmod source. Note that you'll also need to assign Foot
Pedal (CC#04) to control the desired parameter within the
Program or Effect.
Portamento Time (CC#05)
Controls the speed at which portamento will change the
pitch.
Volume (CC#07)
Control the volume of a Program, Combination, or of a
MIDI track in Sequencer modes.
Post IFX Pan (CC#08)
Control the pan after passing through the Insert Effect.
Pan (CC#10)
Control the pan of a Program, of a timbre in a Combination,
or of a MIDI track in Sequencer modes.