Korg Krome Parameter Manual page 193

3. Use Effect to select the desired effect.
4. Use To: Song to specify the song into which the settings
will be inserted, Track to specify the insert-destination
track, Measure to specify the measure and Beat.Tick to
specify the beat and clock at which the settings will be
inserted.
The inserted events are only the effect type and effect
parameters. Settings such as effect on/off and bypass
must be recorded in real time.
Note: Turn back the Location, and play the song to verify
that the effect is switched as you intend.
You can also use the P6: Track Edit menu command Event
Edit to verify that a parameter change System Exclusive
message (Exclusive) has been inserted.
Note: If a pattern had been inserted at the same location
(where you inserted the exclusive data), that pattern will be
expanded to note data.
Using "Put Effect Setting to Track" to switch ef-
fects
The Put Effect Setting to Track menu command inserts
effect settings into a track as exclusive event data. We'll
explain this using two methods as examples.
1) Inserting effect settings at the beginning and in the mid-
dle of a song
We'll set things so that MIDI track 2 uses the insert effect
(IFX3) 035: Stereo Phaser from measures 1 through 8, and
switches to 032: Stereo Flanger from measure 9.
Use the menu command Put Effect Setting to Track to insert
a MIDI parameter change System Exclusive message.
1. In P0–1: Play/REC– Program T01–08, select the desired
program for MIDI track 2.
If you set Track Select to Track 02, you'll be able to monitor
it.
2. In P8: Routing/IFX– Routing T01–08, send MIDI track 2
to IFX3.
3. Specify the effect that you want to use from measure 1.
In P8: Routing/IFX– Insert FX Setup, select 035: Stereo
Phaser for IFX3. Press the On/Off button to turn on the IFX3.
In P8:Routing/ IFX– IFX3, set the parameters as desired.
4. Make sure that you've selected Track 02 in Track Select,
and record as desired.
Sequencer: Menu Command Put Effect Setting to Track
5. In the P8: Routing/IFX page, select the menu command
Put Effect Setting to Track to access the dialog box.
6. Specify the location at which the exclusive message for
the effect will be inserted.
Effect: IFX3
To: Song: 000
Track: 03
Measure: 001
Beat.Tick: 01.000
7. Press the OK button.
8. Specify the effect that you want to use for measure 9
and following.
Go to the P8: Routing/IFX– Insert FX setup, and choose 032:
Stereo Flanger for IFX3.
In the P8: Routing/IFX– IFX3, set the parameters as desired.
9. In the P8: Routing/IFX, choose the Put Effect Setting to
Track menu command to open the dialog box.
10. Specify the location at which the exclusive message for
the effect will be inserted.
Effect: IFX3
To: Song: 000
Track: 03
Measure: 009
Beat.Tick: 01.000
11. Press the OK button.
12. When you play back after executing these commands,
the effect on track 3 will change to 032: Stereo Flanger
at measure 9.
13. If you press the COMPARE button (it will light up) and
play back, the playback will occur as it did before you
executed Put Effect Setting to Track.
14. In the P6: Track Edit– Track Edit page, set Track Select
to Track 03, and choose the Event Edit menu command
to access the event edit screen. (In the Set Event Filters
dialog box, check Exclusive.)
Notice that a MIDI parameter change System Exclusive
message is inserted at the beginning and at measure 9 of
track 3.
2) Using the song's own effect settings from the beginning
of the song, and inserting effect settings from elsewhere
into the middle of the song
In this example, we'll apply an insert effect (IFX3) to MIDI
track 3, and set our parameters so that it uses 035: Stereo
Phaser from the beginning of the song. At measure 9, we'll
insert a MIDI parameter change System Exclusive message
to make IFX3 switch to the 032: Stereo Flanger effect settings
that were created for a different song.
1. Select a desired program for MIDI track 3, and send it
to IFX3.
Make the following settings for MIDI track 3.
Track Select: Track 03 (P0)
Bus (IFX/Output) Select: IFX3 (P8)
In the P0–1: Play/REC– Program T01–08 page, assign a
program to track 3. Then use the P8: Insert Effect page to
route track 3 to the effect, and make effect settings.
2. Make sure that you've selected Track 03 in Track Select,
and record on it.
3. On a separate song you copied, make the effect settings
that you want start using at measure 9.
1) Create song S001.
185