HP 1660CS-Series User Manual page 342

Pod threshold, 7-10, 7-32
ECL, 7-32
TTL, 7-32
User, 7-32
Port in, 4-15
Port out, 4-12
Post-processing features
chart menu, 7-65
compare menu, 7-67
Power requirements, 1-3, 12-3
Power-up tests, 12-14
Preparation for use, 12-3 to 12-6
Preprocessor problems, 10-5
erratic trace measurements, 10-7
slow clock, 10-6
target system will not boot up, 10-5
Preset ECL values, 7-75
Preset field, 7-75
Preset TTL values, 7-75
Preshoot, 7-101
Print
all, 7-20
disk, 7-19
field, 7-19
partial, 7-20
Print to disk
ACSII, 7-19
B/W TIFF, 7-19
EPS, 7-19
PCX, 7-19
Printer, 7-26
Centronics, 2-8
HP-IB setup, 2-5 to 2-6
interface, 7-26
parallel, 2-8, 7-28
RS-232 , 2-7
supported, 2-2
Probe attenuation factor, 7-75
Probe attenuation factor range, 7-75
Probe Cables, 7-10
Probe Connecting
disconnecting probes from pods, 7-14
grabbers to probes, 7-15
pods to probe cables, 7-13
probe cables to analyzer, 7-12 to 7-13
Probe field, 7-75
Probe leads, 7-9
Probe tip assemblies, 7-8
Probing, 7-5 to 7-15
assembly, 7-12 to 7-15
general purpose, 7-6
General Purpose Probing, 7-6
grabbers, 7-10
maximum probe input voltage, 7-11
microprocessor and bus, 7-6
minimal signal amplitude, 7-10
options, 7-5
oscilloscope, 7-11
pod thresholds, 7-10
probe and pod grounding, 7-9
probe cable, 7-10
probe leads, 7-9
probe tip assemblies, 7-8
termination adapter, 7-7
Problems, 10-2
Programming
See HP 1660C/CS Logic Analyzers
Programmers Guide
Protocol
defined, 7-28
Pulse limits
test minimum and maximum, 5-18
Purge, 7-23
R
Range specifiers, 8-12
Range terms, 9-15
Real Time Clock Adjustment, 7-29
Recursive call triggering, 5-8
Reference Listing field, 7-68
Registers
verifying correct storage, 5-13
Rename, 7-23
Repetitive measurements
automating, 6-4
Resource terms, 7-51 to 7-53
assigning, 7-52, 7-53
bit patterns, 7-51
edge terms, 7-51
range terms, 7-51
timers, 7-51 to 7-52
using bit by bit, 7-53
Resources, 9-16
Rolling data, 7-21
RS-232-C
cable, 7-28
Index
interface, 7-26 to 7-28
printers, 2-7
Run field, 7-20
Run key, 7-72
Run repetitive, 7-20
Run until time X-O
field, 7-92
Greater Than field, 7-93
In Range field, 7-93
Less Than field, 7-92
Less Than field resolution, 7-93
Not In Range field, 7-93
Run/Stop options, 7-71
Running the oscilloscope
using Autoscale, 7-71
S
s/Div field, 7-73
Sample period
Time interval mode, minimum, 8-5
timing analyzers, 4-19
Sampling methods
blind time, 8-9
Saving
menus or measurements as images, 6-8
to a flexible disk or internal drive, 6-4
Scope
Auto Measure menu, 3-9, 7-97
Autoscale menu, 7-72
Calibration menu, 3-9, 12-8
Channel menu, 3-8, 7-74
Display menu, 3-8, 7-76
Marker menu, 7-88
Markers menu, 3-9
Trigger menu, 3-9, 7-79
Screen images, 6-2, 6-8, 7-19
Secondary branch, 9-14
Select key, 7-17
Selecting
fields, 1-2, 3-4
SPA modes, 8-6
State Histogram Mode, 8-6
State Overview Mode, 8-6
Time Interval Mode, 8-6
waveforms display, 7-61
Selecting fields
display, 8-21
with mouse, 2-3
Index–5