Siemens SIPROTEC Manual page 687

Addr. Parameter
1123 Angle K0(> Z1)
1124 center phase
1125 C0/C1
1126 RM/RL ParalLine
1127 XM/XL ParalLine
1128 RATIO Par. Comp
1130A PoleOpenCurrent
1131A PoleOpenVoltage
1132A SI Time all Cl.
1133A T DELAY SOTF
1134 Line Closure
1135 Reset Trip CMD
1136 OpenPoleDetect.
1140A I-CTsat. Thres.
1150A SI Time Man.Cl
1151 SYN.MAN.CL
1152 Man.Clos. Imp.
1155 3pole coupling
1156A Trip2phFlt
1161 VECTOR GROUP U
1162 VECTOR GROUP I
1163 TRANS STP IS
1201 STATE OF DIFF.
1210 I-DIFF>
1213 I-DIF>SWITCH ON
1217A T-DELAY I-DIFF>
1218 T3I0 1PHAS
1219A I> RELEASE DIFF
1221 Ic-comp.
1224 IcSTAB/IcN
1233 I-DIFF>>
SIPROTEC, 7SD5, Manual
C53000-G1176-C169-5, Release date 02.2011
Function C
P.System Data 2 -180.00 .. 180.00 °
P.System Data 2 unknown/sym.
Phase 1
Phase 2
Phase 3
P.System Data 2 0.01 .. 10.00
P.System Data 2 0.00 .. 8.00
P.System Data 2 0.00 .. 8.00
P.System Data 2 50 .. 95 %
P.System Data 2 1A 0.05 .. 1.00 A
5A 0.25 .. 5.00 A
P.System Data 2 2 .. 70 V
P.System Data 2 0.01 .. 30.00 sec
P.System Data 2 0.05 .. 30.00 sec
P.System Data 2 only with ManCl
I OR U or ManCl
CB OR I or M/C
I or Man.Close
P.System Data 2 CurrentOpenPole
Current AND CB
Pickup Reset
P.System Data 2 OFF
Current AND CB
w/ measurement
P.System Data 2 1A 0.2 .. 50.0 A; ∞
5A 1.0 .. 250.0 A; ∞
P.System Data 2 0.01 .. 30.00 sec
P.System Data 2 with Sync-check
w/o Sync-check
NO
P.System Data 2 (Setting options depend
on configuration)
P.System Data 2 with PICKUP
with TRIP
P.System Data 2 3pole
1pole leading Ø
1pole lagging Ø
P.System Data 2 0 .. 11
P.System Data 2 0 .. 11
P.System Data 2 Solid Earthed
Not Earthed
Diff. Prot OFF
ON
Diff. Prot 1A 0.10 .. 20.00 A
5A 0.50 .. 100.00 A
Diff. Prot 1A 0.10 .. 20.00 A
5A 0.50 .. 100.00 A
Diff. Prot 0.00 .. 60.00 sec; ∞
Diff. Prot 0.00 .. 0.50 sec; ∞
Dis. General
Diff. Prot 1A 0.10 .. 20.00 A; 0
5A 0.50 .. 100.00 A; 0
Diff. Prot OFF
ON
Diff. Prot 2.0 .. 4.0
Diff. Prot 1A 0.8 .. 100.0 A; ∞
5A 4.0 .. 500.0 A; ∞
Setting Options Default Setting
0.00 °
unknown/sym.
0.75
0.00
0.00
85 %
0.10 A
0.50 A
30 V
0.10 sec
0.25 sec
I or Man.Close
CurrentOpenPole
w/ measurement
20.0 A
100.0 A
0.30 sec
NO
None
with TRIP
3pole
0
0
Solid Earthed
ON
0.30 A
1.50 A
0.30 A
1.50 A
0.00 sec
0.04 sec
0.00 A
0.00 A
OFF
2.5
1.2 A
6.0 A
Appendix
A.7 Settings
Comments
Zero seq. comp. angle, higher
zones >Z1
center phase of feeder
Compensation factor C0/C1
Mutual Parallel Line comp. ratio
RM/RL
Mutual Parallel Line comp. ratio
XM/XL
Neutral current RATIO Parallel
Line Comp
Pole Open Current Threshold
Pole Open Voltage Threshold
Seal-in Time after ALL closures
minimal time for line open before
SOTF
Recognition of Line Closures
with
RESET of Trip Command
open pole detector
CT Saturation Threshold
Seal-in Time after MANUAL clo-
sures
Manual CLOSE COMMAND
generation
MANUAL Closure Impulse after
CONTROL
3 pole coupling
Trip type with 2phase faults
Vector group numeral for voltage
Vector group numeral for current
Transformer starpoint is
State of differential protection
I-DIFF>: Pickup value
I-DIFF>: Value under switch on
condition
I-DIFF>: Trip time delay
Delay 1ph-faults (comp/isol. star-
point)
Min. local current to release
DIFF-Trip
Charging current compensation
Ic Stabilising / Ic Nominal
I-DIFF>>: Pickup value
687