Adjusting Dehumidification Settings; Feature Screen — Dehumidification Settings; Complete Icomfort; System - Adjusting Dehumidification Settings (Non-Communicating Outdoor Unit) - Lennox iComfort Wi-Fi Setup Manual

Complete iComfort

SYSTEM DEVICES SCREEN — DEHUMIDIFICATION SETTINGS
Pre-adjustment REQUIREMENTS:
1st, the device has been installed
2nd, from the "Add or Remove Non-communicating
equipment?", press next.
3rd, in the "Adjust a setting..." screen, configure the
device as follows:
system devices
System
Air Conditioner
Furnace
Thermostat
Humiditrol
System
3rd Stage Delay
4th Stage Delay
Lock In 2nd Stage HP by Outdoor Temp
Balance Point Control
Humiditrol Comfort Adjust
Min De-humidification Setpoint
Humiditrol Comfort Adjust
Select one
Maximum Overcooling
Minimum Overcooling
3a
save
Humiditrol Comfort Adjust settings are
only available on units equipped with
®
a Humiditrol De-humidification
device.
Figure 12. Complete iComfort
FEATURE SCREEN — DEHUMIDIFICATION SETTINGS
1. From the Main Screen, press the right arrow icon to go the
the Features screen.
2. From the Features screen, select system settings.
3. Touch the ClimateIQ setting button. Available options
when selected are selection for DRY, MODERATE and
HUMID.
4. Selecting HUMID bring on the set-to button. When you
touch the set-to button, the arrows appear, allowing you to
change to the desired dehumidifier percentage setting
COOLING MODE — CLIMATE IQ™
Three climate settings are available:
•
Dry ­ The system supplies higher indoor airflow at all com­
pressor capacities, increasing efficiency by operating at a
higher sensible-to-total ratio.
•
Moderate ­ The system supplies indoor airflow that balances
efficiency and comfort.
•
Humid - The system supplies lower indoor airflow at all com­
pressor capacities, improving humidity removal by operating
at a lower sensible to total ratio.
507343-01
®
System — Adjusting Dehumidification Settings
To adjust a setting,
highlight it,
then press Edit
System
1a
1b
De-humidification Control Mode
current value:
Midpoint Overcooling
2a
2b
Midpoint Overcooling
back
System
Staged Delay TImers
cancel
2nd Stage Delay
3b
3rd Stage Delay
4th Stage Delay
Lock In 2nd Stage HP by Outdoor Temp
Balance Point Control
Humiditrol Comfort Adjust
Min De-humidification Setpoint
OD/Humid Boundary
Outdoor Temperature Reading Calibr
9:39 am Aug 15, 2012
Figure 13. Dehumidification iComfort
1. In the "system devices" list, use the arrows (1a) to
highlight System. Press edit (1b).
2. Humiditrol
rows (2a) to highlight Humiditrol Comfort Adjust.
The current value defaults to Maximum Overcooling.
Press edit (2b).
3. Humiditrol
(3a) to select the overcooling level; press save (3b).
about
(After saving, check that the current value now shows
resetAll
the new selection).
4. Use arrows (4a) to highlight Min De-humidification
edit
Setpoint; press edit (4b). Note the current value
reinstall (e.g. 45).
5. Use arrows (5a) to make changes; press save (5b).
(After saving, check that the current value now shows
reset
the new selection).
edit
6. Press the back button to return to "Adjust a setting..."
screen.
De-humidification Control Mode
current value:
45
4a
6
back
®
System Devices — Dehumidification Settings
SYSTEM SETTINGS
Appears only when
heat pump is
present
heating
mode
COMFORT
Wi-Fi
9:39 am Aug 15, 2012
HEATING MODE (XP25 ONLY) — CLIMATE IQ™
This technology optimizes dehumidification settings
for specific climates to improve home comfort during
cooling or heating operations.
Two climate settings are available:
•
Comfort ­ The system reduces indoor airflow, in­
creasing supply air temperature.
•
Normal ­ Standard system operation.
®
System Controls
Page 16
®
only—In the "System" list, use the ar­
®
only—Touch one of the radio buttons
Min De-humidification
Setpoint
4b
Range is 40 to 60
Default is 45, inc:1
edit
set-to
reset
42 %
5b
save
(returns to
adjust a
setting
screen)
humidification
De-humidification settings
settings
%
35 ClimateIQ
humidifier
setting
is ON
set to
MOD
(default is ON) (default is DRY)
Select the humidity
level that matches
your environment
5a
cancel
humidifier
%
40
display
is ON
set to
(default is ON)
?