Diagnosis And Testing - Power Locks; Standard Procedure - Toggling Customer Preferences; Deck Lid Release Solenoid; Diagnosis And Testing - Deck Lid - Chrysler 2004 Concorde Service Manual

LH
POWER LOCKS (Continued)
CHILD PROTECTION LOCK
The lock when engaged, will disable the inside door
handle from opening the door. The lock is part of the
latch/lock assembly. The lock is engaged by moving a
lever that is located on the rearward inside edge of
the door.
DOOR LOCK INHIBIT
With the key in the ignition switch and the driver's
door open, the Body Control Module (BCM) will
ignore the command to lock the power door locks.
Once the key is removed, or the driver's door is
closed, the BCM will allow the power door locks to
lock.
REMOTE KEYLESS ENTRY
The transmitter has four buttons for operation.
They are LOCK, UNLOCK, DECK LID RELEASE,
and PANIC.
• The UNLOCK button will unlock the driver's
door and enable illuminated entry. Pushing and
releasing the button once will unlock the driver's
door. Pushing and releasing the button two times,
within a five second interval, will unlock all doors.
• Upon pressing the LOCK button, the horn will
sound a short CHIRP (if enabled) and flash the park
lamps (if enabled) to notify that the all door lock sig-
nal was received and set. Illuminated entry is can-
celled and the interior lamps are faded to off.
• Pushing
and
RELEASE button (immediate release or press and
hold release) within a two second interval, will
slightly ajar the deck lid.
• Pushing and holding the PANIC button will
cause the panic alarm to sound for three minutes,
until the panic button is pressed and held a second
time, or the vehicle reaches a speed of 15 mph.
The receiver is capable of retaining a Vehicle
Access Code (VAC) even when power is removed.
Each Remote Keyless Entry (RKE) module must
have at least one and no more than four transmit-
ters.
HORN CHIRP TOGGLE
This can be done using a DRB III scan tool or by
the customer. The horn chirp will enter the opposite
state of its current programmed state by receiving
this operation code. The BCM is responsible for keep-
ing track of the horn chirp status.
releasing the DECK

DIAGNOSIS AND TESTING - POWER LOCKS

The most reliable, efficient, and accurate
means to diagnose the power lock system
requires the use of a DRBIII scan tool and the
proper Diagnostic Procedures manual.
STANDARD PROCEDURE - TOGGLING
CUSTOMER PREFERENCES
DECK LID RELEASE TOGGLE
Deck lid release toggle is programmed to immedi-
ate release or press and hold release by continually
pressing the unlock button for a minimum of 4 sec-
onds to a maximum of 10 seconds. Within the 4-10
second range, the deck lid release button is
depressed. Both buttons are then released.
HORN CHIRP TOGGLE
Once the transmitters have been programmed, the
horn chirp can be enabled/disabled by sending the
horn chirp toggle operation code to the Body Control
Module (BCM). This can be done by pressing and
holding the RKE Lock button for over four seconds.
While pressing the Lock button, press the Unlock
button. The horn chirp will enter the opposite state
of its current programmed state by receiving this
operation code. The BCM is responsible for monitor-
ing of the horn chirp status.
LID
DECK LID RELEASE
SOLENOID

DIAGNOSIS AND TESTING - DECK LID

RELEASE

For vehicles equipped with electric deck lid release.
(1) Confirm motor lead wire is connected and 10
volts or more are available at solenoid.
(2) Provide proper ground through latch mounting
screws.
(3) Remove latch and examine plunger. Plunger
should spring back when pressed.
(4) Insure that solenoid plunger travel is adequate
approximately 16 mm (5/8 inch).

REMOVAL

(1) Disconnect and isolate the negative battery
cable remote terminal from the remote battery post.
(2) Raise deck lid to the full up position.
(3) Remove latch cover attaching screws then
remove cover.
(4) Remove two mounting motor screws and
remote key cable retainers then remove motor.
POWER LOCKS 8N - 3