Removal; Rear Seat Belt & Retractor Removal; Installation - Chrysler 2004 Concorde Service Manual

8O - 20 RESTRAINTS
PASSENGER AIRBAG (Continued)
(17) Lift the steering column into position and
install the four steering column nuts.
(18) Connect the two center instrument panel
ground eyelets on the left side of the floor tunnel.
(19) Connect the Occupant Restraint Controller
(ORC) electrical connector.
(20) Install the bulkhead connector mounting
screw.
(21) Connect the brake switch electrical connector.
(22) Install the left (driver's) side air distribution
ducts.
(23) Install the two center instrument panel lower
attaching nuts.
(24) If not equipped with center console, install the
center lower instrument panel floor bin.
(25) If equipped with console, install the left
instrument panel side cover.
(26) Connect the heater - A/C control unit and
traction control switch (if equipped) electrical connec-
tors and install the instrument panel center bezel.
(27) Install the left knee blocker.
(28) Connect the hood release cable and decklid
release electrical connector. Install the left lower
instrument panel trim cover.
(29) Install the left instrument panel end cover.
(30) Install the left and right A-pillar trim mold-
ings.
(31) Accessing through the glove box door, install
five screws to the glove box close - out assembly.
Torque screws to 2.3 N·m (20 in. lbs.) (Fig. 20).
(32) If equipped with center console:
• Install the right console side trim panel.
• Install the console shifter bezel.
• Install the gearshift handle and set screw.
(33) Install the right instrument panel end cover.
(34) Install the four screws that attach the glove
box door to the instrument panel and install the
glove box door.
WARNING: DO NOT CONNECT THE BATTERY NEG-
ATIVE CABLE REMOTE TERMINAL. REFER TO
ELECTRICAL, RESTRAINTS, DIAGNOSIS AND TEST-
ING - AIRBAG SYSTEM FIRST.
DEPLOYED AIRBAG
(1) Transfer all instrument panel components
which are not damaged to NEW instrument panel
and pad assembly. Tighten screws to 2.3 N·m (20 in.
lbs.) torque.
(2) Install the four screws to the airbag reinforce-
ment brace on the airbag. Torque screws to 2 N·m
(20 in. lbs.) (Fig. 22).
(3) Install the airbag assembly into the instrument
panel retainer.
(4) Install the five screws attaching the passenger
airbag assembly to retainer. Torque screws to 2 N·m
(20 in. lbs.) (Fig. 21).
(5) Install the four 10 mm hex head screws to the
deployment door reinforcement - two screws per side.
Torque screws to 8.5 N·m (75 in. lbs..) (Fig. 21)
(6) Connect the NEW instrument panel wiring
harness to the airbag reinforcement bracket.
(7) Install the right and left pencil strut to Passen-
ger Airbag screws. Torque screws to 5 N·m (45 in.
lbs.) (Fig. 21).
(8) Connect the yellow wire harness connector to
the airbag assembly and the three push pin fasten-
ers. Align the connector, then firmly press straight
in, being careful not to damage pins on airbag.
(9) Install the two screws to the right distribution
duct assembly. Torque screws to 2 N·m (20 in. lbs.).
(10) Install the four screws to the right demister
duct. Torque screws to 2 N·m (20 in. lbs.)
Install the instrument panel. Refer to Body, Instru-
ment Panel, Installation.
WARNING: DO NOT CONNECT THE BATTERY NEG-
ATIVE CABLE REMOTE TERMINAL. REFER TO
ELECTRICAL, RESTRAINTS, DIAGNOSIS AND TEST-
ING - AIRBAG SYSTEM FIRST.
REAR SEAT BELT &
RETRACTOR

REMOVAL

WARNING: INSPECT THE CONDITION OF THE
SHOULDER/LAP BELT. REPLACE THE RETRACTOR
IF THE BELT IS CUT, FRAYED, TORN, OR DAM-
AGED IN ANY WAY.
(1) Remove the seat cushion and back.
(2) Remove the upper quarter trim panel.
(3) Remove the lower quarter trim panel.
(4) Remove the nut attaching the lower seat belt
anchor to the floor.
(5) Remove the turning loop bolt.
(6) Remove the bolt attaching the seat belt retrac-
tor to the quarter panel. (Fig. 23).
(7) Remove the seat belt retractor from the vehicle.

INSTALLATION

WARNING: INSPECT THE CONDITION OF THE
SHOULDER/LAP BELT. REPLACE THE RETRACTOR
IF THE BELT IS CUT, FRAYED, TORN, OR DAM-
AGED IN ANY WAY.
(1) Place belt in position in the vehicle.
LH