Installation; Occupant Restraint Controller - 6 Passenger Vehicles Removal - Chrysler 2004 Concorde Service Manual

8O - 16 RESTRAINTS
OCCUPANT RESTRAINT CONTROLLER - 5 PASSENGER VEHICLES (Continued)
(11) With the ORC now exposed, slide the red Con-
nector Position Assurance (CPA) tab out. Press down
on the locking latch and disconnect the ORC 23-way
connector.
(12) Remove the two side module mounting screws
on the drivers side.
(13) Loosen the top screw on the drivers side.
(14) Lift up the module and slide out the ORC.
NOTE: If the ORC cannot be lifted out, the passen-
ger side screw needs some additional loosening.
(15) Remove the ORC from vehicle.

INSTALLATION

WARNING: THE ORC IS A SAFETY MODULE AND
FAILURE TO INSTALL AND SECURE IT PROPERLY,
COULD CAUSE THE MODULE TO POSSIBLY MAL-
FUNCTION AND CAUSE PERSONAL INJURY.
(1) Position the ORC (arrow pointing forward in
vehicle) on the ORC mounting bracket. The mounting
bosses on the controller will correctly position the
ORC on the bracket. Attach the ORC to the bracket
with the three screws supplied and torque to 88 to
124 in. lbs. (10 to 14 N·m).
CAUTION: USE SUPPLIED SCREWS ONLY.
(2) Tighten the top screw on the drivers side.
(3) Install the two side ORC mounting screws on
the drivers side.
(4) Connect ORC 23-way connector and slide the
red Connector Position Assurance (CPA) tab in.
NOTE: If working on a Concorde, the Instrument
Panel must be installed. Refer to Body, Instrument
Panel for Installation and then go to Electrical,
Restraints, Diagnosis and Testing - Airbag System.
(5) Install left console side panel and two retaining
screws.
(6) Install the right console side panel.
(7) Install the screws in the upper and lower left
corner or the glove box bin.
(8) Close the glove box door.
(9) Install the steering wheel cover and the two
screws to steering column cover.
(10) Install the left instrument panel end cover
covering the junction block.
(11) Connect power outlet connector and install the
center bezel into vehicle.
(12) Install the two screws to shifter bezel.
(13) Install the one screw to shift knob.
WARNING: DO NOT CONNECT THE BATTERY NEG-
ATIVE CABLE REMOTE TERMINAL. REFER TO
ELECTRICAL, RESTRAINTS, DIAGNOSIS AND TEST-
ING - AIRBAG SYSTEM FIRST.
OCCUPANT RESTRAINT
CONTROLLER - 6 PASSENGER
VEHICLES
REMOVAL
(1) Open hood and disconnect the negative battery
cable remote terminal from the remote battery post.
(2) Wait two minutes for the system reserve capac-
itor to discharge before servicing any airbag compo-
nents.
(3) Open glove box door and release side tabs and
swing down.
NOTE: If working on a Concorde, the Instrument
Panel must be removed. Refer to Body, Instrument
Panel, for Removal. Then go to Step 11.
(4) Remove the left endcap at the junction block.
(5) Remove two screws to steering column cover
then pull toward rear of vehicle to disengage clips.
(6) Open glove box door. Continue to pull down on
the door until the glove box drops and you see the
screws in the upper and lower left corner or the glove
box bin.
(7) Remove the instrument panel center bezel. The
temperature control module, power outlet and trac-
tion control switch will pop out with the center bezel.
(8) Disconnect the connectors at center bezel.
(9) Remove four screws to Chin bezel. Two on the
right side and two on the left side of vehicle.
(10) Remove one screw and one push fastener
retaining floor bin.
(11) With the ORC now exposed, slide the red Con-
nector Position Assurance (CPA) tab out. Press down
on the locking latch and disconnect the ORC 23-way
connector.
(12) Remove the two side module mounting screws
on the drivers side.
(13) Loosen the top screw on the drivers side.
(14) Lift up the module and slide out the ORC.
NOTE: If the ORC cannot be lifted out, the passen-
ger side screw needs some additional loosening.
(15) Remove the ORC from vehicle.
LH