Monitoring Station Communication Setting; Reporting Code Setting - jablotron MAESTRO JA-65 Installation Manual

16. Monitoring station communication setting

This part of the manual is intended only for the use of specialists involved in monitoring. We recommend to use a
computer equipped with Comlink program for complete setting of the monitoring station communication (see 19).
Changes of the setting can also be performed manually using the keypad:
•
Enter the programming mode (entering F 0 SC - SC = Service Code, factory default SC=6060), indicated by a „P" on the LED
display.
•
To exit the programming mode, press the N key („P" will turn off).
Monitoring station communication parameters
Sequence
0 001 xx Reporting codes table (see part 18)
to where: x= 0 – 9, F0 = A
0 198 xx if 00 is set, the event is not reported
0 2 xxxx Account code (4 digits, for 3/1 and 3/2 formats the structure is 0xxx)
x = 0 – 9 (hexadecimal codes can be used too - see above)
0 3 xy Protocol x:
0 = Ademco Slow
1 = Ademco Fast
2 = Telemax
3 = Franklin
4 = Radionics 2300
0 4 x Re-dialing pause, x= 1 – 9 (x 10 min.)
0 6 xx..xFy Phone numbers xx...x to memory y (1 and 2), pause = F0
0 9 6060 Communicator reset to factory default settings
Dialing method ( tone / pulse) and telephone line checking has a common setting with the voice & Pager message setting - see part 14.4. and 14.6.
Notes:
Some of the protocols are not standardized
and some manufacturers of Monitoring Station
receivers use different parameters in some of
their protocols. Therefore Jablotron cannot
guarantee full compatibility with all Monitoring
Station receivers.
If the connection with the Monitoring Station is
not available, the events are queued in the
communicator's memory and are transmitted in
one burst as soon as the connection is
established. All events are reported to the
Monitoring Station in the same order as they
happened.
Once communication has started, it can not
be interrupted unless the control panel is

16.1. Reporting code setting

These sequences can be used to program the report codes for all possible events. Depending on the used protocol and
format, different amounts of data should be entered. The complete report code programming table is shown in section 18.
The setting sequence structure is as follows:
0 x x x r c
If the reporting code 00 is programmed, the event will not be reported to the Monitoring Station.
Factory setting: 00 for all events
Notes:
•
Abbreviation "Rc" is used in the report code programming table for the major events group. Only the first digit of this group of codes
is transmitted when formats 3/1 or 4/1/1 are used. Other formats use both digits of the "Rc" and "rc" report codes.
•
The Contact ID (CID) is an automatic protocol. If you enter any report code other than zero for a major event (Rc), all events of this
type will be transmitted automatically including all details regarding the event source. Internal structure of the CID protocol is shown
in the part 18.1. This protocol provides the most in-depth data for the monitoring station and its use is recommended by Jablotron.
•
The Sur Guard protocol has 4/2 structure plus one more digit which is generated automatically (see 16.3.)
•
If the control panel is split and only one section is armed, then a partial arming report code is sent. If all sections are armed, a
complete arming report code is sent. If the system was completely armed and only one section is disarmed, the disarming report
code will be sent and then it will be followed by the partial arming report code.
Alarm system JA-65 MAESTRO
Description
, F1 = B
h h
5 = Radionics 1400
6 = DTMF 2300
7 = Sur Guard
8 = Ademco Express
9 = Contact ID
switched to the programming or to the user
mode. For example, if the user causes a false
alarm and then cancels it, both events are sent
to Monitoring Station.
Events occurring while the JA-65 control
panel is in a programming or user mode are
reported to the Monitoring Station after the
closing of these modes. (They are stored in the
memory and reported together with reporting
codes describing the change of operation
modes.)
When
communication to the monitoring station has
the highest priority (voice and Pager messages
are sent later with lower priority). A User or
Installer
xxx = event number (from 001 to 198)
rc = report code (two digits). For 3/1 and 4/1/1 formats only the first digit of the report code is
used (R). Codes should be entered in a hexadecimal format, with numbers higher than 9
beginning with the F key: A
, F2 = C , F3 = D , F4 = E
h h
Format y:
0 = 3/1 (xxx R)
1 = 3/2 (xxx rc)
2 = 4/1/1 (xxxx Rn)
3 = 4/2 (xxxx rc)
the dialer is activated,
can interrupt the digital
= F0 B = F1 C
h h
- 20 -
Factory default setting
00
, F5 = F
h h
0000
90
1
communication by entering the User mode or
Programming mode. Reset of the control panel
has no influence to the digital communicator's
settings (it is reported to the Monitoring station
as an event).
The RESET of the digital communicator
itself (sequence 0 9 6060), the change of the
Monitoring Station's telephone numbers, the
change of an account number code or the
change of a format setting will erase all the
reporting codes queued in the communicator's
the memory. However the events remain stored in
the control panel's internal memory.
Jablotron recommends use of the MS-
300 monitoring station with ComGuard SW.
dialer
sequences: 00 and 01
= F2 D = F3 E
h h
For all events
Contact ID
10 minutes
erased
-
= F4 F = F5
h h
MFM51202