ZyXEL Communications Prestige 100IH User Manual
  1. Manuals
  2. Brands
  3. ZyXEL Communications Manuals
  4. Wireless Router
  5. Prestige 100IH
  6. User manual
ZyXEL Communications Prestige 100IH User Manual

ZyXEL Communications Prestige 100IH User Manual

Isdn router
Hide thumbs Also See for Prestige 100IH:
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
Prestige 100IH
ISDN Router
User's Guide
Version 2.41
Feb 2000
ZyXEL
T
I
A
S
OTAL
NTERNET
CCESS
OLUTION

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Prestige 100IH and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ZyXEL Communications Prestige 100IH

Summary of Contents for ZyXEL Communications Prestige 100IH

  • Page 1 Prestige 100IH ISDN Router User's Guide Version 2.41 Feb 2000 ZyXEL OTAL NTERNET CCESS OLUTION...
  • Page 3 ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein.
  • Page 4 P100IH ISDN Router manufactured functionally equivalent product of equal value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. Note Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser.

  • Page 5: Customer Support

    Corp., 6 Innovation Road II, support@europe.zyxel.com www.europe.zyxel.com Worldwide Science-Based Industrial Park, HsinChu, Taiwan. sales@zyxel.com.tw +886-3-578-2439 ftp.europe.zyxel.com support@zyxel.com +1-714-632-0882 www.zyxel.com ZyXEL Communications Inc., North 800-255-4101 1650 Miraloma Avenue, America Placentia, CA 92870, U.S.A. sales@zyxel.com +1-714-632-0858 ftp.zyxel.com support@zyxel.dk +45-3955-0700 www.zyxel.dk ZyXEL Communications A/S,...

  • Page 7: Table Of Contents

    Features of the Prestige........................ 1-1 Applications for Prestige 100IH ....................1-4 Chapter 2: Hardware Installation & Initial Setup ..................2-1 Prestige 100IH Rear Panel and Connections ................2-2 Additional Installation Requirements ..................2-3 Power On Your Prestige ......................2-4 Navigating the SMT Interface ..................... 2-5 Changing the System Password ....................
  • Page 8 P100IH ISDN Router SUA (Single User Account) Versus NAT ..................4-4 SMT Menus..........................4-5 Configuring NAT .........................4-7 Examples ............................4-15 Chapter 5: Remote Node Configuration.......................5-1 Remote Node Setup........................5-1 Chapter 6: Remote Node TCP/IP Configuration ..................6-1 LAN-to-LAN Application ......................6-1 Chapter 7: Dial-in Server Configuration ......................7-1 Remote Access Server ........................7-2 Default Dial-In Setup ........................7-3 Dial-In Users Setup ........................7-7...
  • Page 9 P100IH ISDN Router 10.2 Telnet Under NAT ........................10-1 10.3 Telnet Capabilities ........................10-2 Chapter 11: System Maintenance ......................11-1 11.1 System Status..........................11-2 11.2 Log and Trace ..........................11-6 11.3 Diagnostic ..........................11-9 11.4 Backup Configuration......................11-12 11.5 Restore Configuration......................11-13 11.6 Firmware Upload ........................

  • Page 10: List Of Figures

    Figure 1-2 LAN-to-LAN Connection Application ..................1-5 Figure 1-3 Telecommuting/Remote Access Server Application ..............1-6 Figure 2-1 Front Panel Of P100IH .......................2-1 Figure 2-2 Prestige 100IH Rear Panel and Connections ................2-2 Figure 2-3 Power-On Display ........................2-4 Figure 2-4 Login Screen..........................2-4 Figure 2-5 SMT Main Menu ........................2-6 Figure 2-6 Menu 23.1 - System Password....................2-7...
  • Page 11 P100IH ISDN Router Figure 4-10 Editing The First Rule in a Set....................4-11 Figure 4-11 Editing The Second Rule in a Set................... 4-12 Figure 4-12 Multiple Servers Behind NAT ....................4-13 Figure 4-13 Menu 15.2 – NAT Server Sets ....................4-14 Figure 4-14 Menu 15.2.1 –Multiple Server Configuration ................
  • Page 12 P100IH ISDN Router Figure 7-3 Menu 13 – Default Dial-in Setup....................7-4 Figure 7-4 Default Dial-in Filter ........................7-7 Figure 7-5 Menu 14 - Dial-in User Setup.....................7-8 Figure 7-6 Edit Dial-in User.........................7-8 Figure 9-1 Filter Rule Process........................9-2 Figure 9-2 Outgoing Packet Filtering Process....................9-3 Figure 9-3 Menu 21 - Filter Set Configuration.....................9-4 Figure 9-4 Menu 21.1 - Filter Rules Summary.....................9-5 Figure 9-5 Menu 21.2 - Filter Rules Summary.....................9-5...
  • Page 13 P100IH ISDN Router Figure 11-12 HyperTerminal Screen ...................... 11-12 Figure 11-13 Successful Backup ......................11-13 Figure 11-14 Restore Configuration ....................... 11-13 Figure 11-15 HyperTerminal Screen ...................... 11-13 Figure 11-16 Successful Restoration ...................... 11-14 Figure 11-17 Menu 24.7 - System Maintenance - Upload Firmware ............. 11-14 Figure 11-18 Menu 24.7.1 - Uploading Router Firmware ..............
  • Page 14 P100IH ISDN Router List of Tables Table 2-1 LED functions ..........................2-1 Table 2-2 Main Menu Commands........................2-5 Table 2-3 Main Menu Summary ........................2-6 Table 2-4 General Setup Menu Fields......................2-9 Table 2-5 Menu 2 – ISDN Setup ........................2-11 Table 3-1 DHCP Ethernet Setup Menu Fields .....................3-5 Table 3-2 TCP/IP Ethernet Setup Menu Fields ....................3-6 Table 3-3 Internet Account Information.......................3-7 Table 3-4 Internet Access Setup Menu Fields....................3-8...
  • Page 15 P100IH ISDN Router Table 8-2 Supplemental Services by switch type..................8-2 Table 8-3 Phone Flash Commands ......................8-5 Table 9-1 Abbreviations Used in the Filter Rules Summary Menu............. 9-5 Table 9-2 Abbreviations Used If Filter Type Is IP ..................9-6 Table 9-3 Abbreviations Used If Filter Type Is GEN.................

  • Page 17: Preface

    Congratulations on your purchase of the Prestige ISDN Router. Don’t forget to register your Prestige (fast, easy online registration at www.zyxel.com) for free future product updates and information. The Prestige 100IH is a high-performance routers that offer complete solutions for your WAN (Wide Area Network) applications such as Internet access, LAN-to-LAN connections, telecommuting and remote access over ISDN (Integrated Service Digital Network).
  • Page 18 P100IH ISDN Router Structure of this Manual Getting Started (Chapters 1-2) This helps you connect, install and setup your Prestige to operate on your network The Internet (Chapter 3) This shows how to configure your Prestige for Internet access. Advanced Applications (Chapters 4-8) This shows how to use your Prestige for more advanced applications.

  • Page 19: Chapter 1: Getting To Know Your Isdn Router

    P100IH ISDN Router Chapter 1: Getting to Know Your ISDN Router Features of the Prestige Time and Date Setting This all new feature allows the Prestige to connect to a time server to synchronize its system clock when it is booting. Call Scheduling The call scheduling feature allows the Prestige to manage a remote node and dictate when a remote node should be called and for how long...
  • Page 20 PPP/MP (Point-to-Point Protocol/Multilink Protocol) link layer protocol. Integrated 4-Port Ethernet Hub The Prestige 100IH is equipped with a built-in 4-port Ethernet 10Base-T hub. The built-in hub eliminates the need to purchase a separate hub when building a one to four-port network. For a larger number of workstations, additional hubs can be daisy-chained to the Prestige.
  • Page 21 P100IH ISDN Router Full Network Management ♦ Accessing SMT (System Management Terminal) through telnet connection. ♦ Windows-based PNC (Prestige Network Commander). Logging and Tracing ♦ CDR (Call Detail Record) to help to analyze and manage the telephone bill. ♦ Built-in message logging and packet tracing. ♦...

  • Page 22: Applications For Prestige 100Ih

    P100IH ISDN Router Upgrade P100IH Firmware via LAN The PCT allows upgrading of the Prestige 100IH firmware over the local LAN. Supplementary Voice Features The Prestige supports the following Supplementary Voice Features on both of its analog, or POTS (Plain Old Telephone Service), phone ports: ♦...

  • Page 23: Figure 1-2 Lan-To-Lan Connection Application

    P100IH ISDN Router Internet Single User Account For a SOHO (small office/Home Office) environment, your Prestige offers the NAT (Network Address Translation) feature that allows multiple users on the LAN (Local Area Network) to access the Internet concurrently for the cost of a single user. NAT address mapping can also be used for other LAN to LAN connections.

  • Page 24: Figure 1-3 Telecommuting/Remote Access Server Application

    P100IH ISDN Router Figure 1-3 Telecommuting/Remote Access Server Application Getting To Know Your Prestige...

  • Page 25: Chapter 2: Hardware Installation & Initial Setup

    Chapter 2: Hardware Installation & Initial Setup 2.1.1 Front Panel LEDs OF P100IH The LED indicators on the front panel indicate the operational status of the Prestige 100IH. The following table describes the LED functions: ISDN PHONE ISDN Hub Router...

  • Page 26: Prestige 100Ih Rear Panel And Connections

    P100IH ISDN Router Prestige 100IH Rear Panel and Connections The figure below shows the rear panel of your Prestige 100IH and the connection diagram. Figure 2-2 Prestige 100IH Rear Panel and Connections Step 1. Connecting a Telephone/Fax to the Prestige You can connect regular telephones, fax machines or other analog devices to the Prestige.

  • Page 27: Additional Installation Requirements

    Ethernet network. Connect one end of a straight through Ethernet cable (white tag) to the NIC on the workstation and the other end to one of the built-in 4 Ethernet ports on the Prestige 100IH (Figure 2-2). Step 5.

  • Page 28: Power On Your Prestige

    When you power on your Prestige, it performs several internal tests as well as line initialization. After the initialization, the Prestige asks you to press Enter to continue, as shown. Copyright (c) 1994 - 2000 ZyXEL Communications Corp. ethernet address: 00:a0:c5:77:03:42 Resetting ISDN firmware.(2) ISDN Firmware DSS1: V 09D...

  • Page 29: Navigating The Smt Interface

    P100IH ISDN Router Navigating the SMT Interface The SMT (System Management Terminal) is the interface that you use to configure your Prestige. Several operations that you should be familiar with before you attempt to modify the configuration are listed in the table below. Table 2-2 Main Menu Commands Operation Press/<read>...

  • Page 30: System Management Terminal Interface Summary

    P100IH ISDN Router After you enter the password, the SMT displays the Main Menu, as shown below. Copyright (c) 1994 – 2000 ZyXEL Communications Corp. Prestige 100IH Main Menu Getting Started Advanced Management 1. General Setup 21. Filter Set Configuration 2.

  • Page 31: Changing The System Password

    System Maintenance This menu provides system status, diagnostics, software upload, etc. Schedule Setup This menu allows the Prestige 100IH to manage a remote node and dictate when a remote node should be called and for how long Exit To exit from SMT and return to the blank screen.

  • Page 32: Resetting The Prestige

    P100IH ISDN Router ZyNOS firmware file (sometimes referred to as the “ras” file) is the file that contains the ZyXEL Network Operating System firmware and the external firmware file is usually called the router model name with a *.bin extension, e.g., P100IH.bin. Rename the configuration filename to “rom-0” and the firmware filename to “ras”...

  • Page 33: Isdn Setup Menus

    P100IH ISDN Router Table 2-4 General Setup Menu Fields Field Description Example System Name Choose a descriptive name for identification purposes. This name can be 100IH up to 30 alphanumeric characters long. Spaces are not allowed, but dashes “-” and underscores "_" are accepted. Location (optional) Enter the geographic location (up to 31 characters) of your Prestige.
  • Page 34 P100IH ISDN Router MSN and Subaddress Depending on your location, you may have Multiple Subscriber Number (MSN) where the telephone company gives you more than one number for your ISDN line. You can assign each number to a different port, e.g., the first number to data calls, the second to A/B adapter 1 and so on. Or (DSS1) the telephone company may give you only one number, but allow you to assign your own subaddresses to different ports, e.g., subaddress 1 to data calls and 2 to A/B adapter 1.

  • Page 35: Figure 2-8 Menu 2 - Isdn Setup For Dss1

    P100IH ISDN Router isdn initstring set AT&ZOx=number where x is 'I' for ISDN data calls, 'A' for A/B Adapter 1 and 'B' for A/B Adapter 2. For instance, isdn initstring set AT&ZOI=100&ZOA=101&ZOB=102 sets the calling party number to 100 for ISDN data calls, 101 for A/B adapter 1 and 102 for A/B adapter 2. Menu 2 - ISDN Setup Switch Type: DSS-1(Taiwan) B Channel Usage= Switch/Switch...

  • Page 36: Advanced Setup

    P100IH ISDN Router PABX Outside Line Enter the number for outside line access if the Prestige is connected to Prefix a PABX; otherwise, leave it blank. The maximum number of digits is You only need to fill in this field if your switch requires a specific Outgoing Calling Outgoing Calling Party Number;...

  • Page 37: 2.10 Ethernet Setup

    P100IH ISDN Router Menu 2.1 - ISDN Advanced Setup Phone 1 Call Waiting= Enable Phone 2 Call Waiting= Enable Calling Line Indication= Enable Figure 2-9 ISDN Advanced Setup When you are finished, press ENTER at the message: ‘Press ENTER to confirm’, the Prestige uses the information that you entered to initialize the ISDN line.

  • Page 38: Figure 2-12 Menu 3.1 - General Ethernet Setup

    This menu allows you to select your Ethernet interface, either 10BaseT or AUI for the Prestige 100 (only 10BaseT for the Prestige 100IH, so this field does not appear) and specify the filter sets that you wish to apply to the Ethernet traffic. You seldom need to filter Ethernet traffic, however, the filter sets may be useful to block certain packets, reduce traffic and prevent security breaches.

  • Page 39: Chapter 3: Internet Access

    P100IH ISDN Router Chapter 3: Internet Access This chapter shows you how to configure the LAN as well as the WAN of your Prestige for Internet access. Factory Ethernet Defaults The Ethernet parameters of the Prestige are preset in the factory with the following values: IP address of 192.168.1.1 with subnet mask of 255.255.255.0 (24 bits).

  • Page 40: Private Ip Addresses

    P100IH ISDN Router The subnet mask specifies the network number portion of an IP address. Your Prestige will compute the subnet mask automatically based on the IP address that you entered. You don’t need to change the subnet mask computed by the Prestige unless you are instructed to do otherwise. 3.2.2 Private IP Addresses Every machine on the Internet must have a unique address.

  • Page 41: Dhcp Configuration

    IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other systems that support the DHCP client. The Prestige 100IH can now also act as a surrogate DHCP server (DHCP Relay) where it relays IP address assignment from the actual real DHCP server to the clients.

  • Page 42: Tcp/Ip Ethernet Setup And Dhcp

    P100IH ISDN Router TCP/IP Ethernet Setup and DHCP You will now use Menu 3.2 to configure your Prestige for TCP/IP. To edit Menu 3.2, select the menu option Ethernet Setup in the Main Menu. When Menu 3 appears, select the submenu option TCP/IP and DHCP Setup and press [Enter] The screen now displays Menu 3.2 - TCP/IP and DHCP Ethernet Setup, as shown next.

  • Page 43: Table 3-1 Dhcp Ethernet Setup Menu Fields

    Server, your Prestige will act as a DHCP server. If set to None, Server (default) DHCP server will be disabled. If the Prestige 100IH is set to Relay, it will act as a surrogate DHCP server where it relays IP...

  • Page 44: Table 3-2 Tcp/Ip Ethernet Setup Menu Fields

    P100IH ISDN Router Follow the instructions in the following table to configure TCP/IP parameters for the Ethernet port. Table 3-2 TCP/IP Ethernet Setup Menu Fields Field Description Example TCP/IP Setup Enter the IP address of your Prestige in dotted decimal notation 192.168.1.1 Address (default)

  • Page 45: Internet Access Configuration

    P100IH ISDN Router Internet Access Configuration Menu 4 allows you to enter the Internet Access information in one screen. Menu 4 is actually a simplified setup for one of the remote nodes that you can access in Menu 11. Before you configure your Prestige for Internet access, you need to collect your Internet account information from your ISP.

  • Page 46: Figure 3-2 Menu 4 - Internet Access Setup

    P100IH ISDN Router From the Main Menu, enter option Internet Access Setup to go to Menu 4 - Internet Access Setup, as displayed below. The following table contains instructions on how to configure your Prestige for Internet access. Menu 4 - Internet Access Setup ISP's Name= ? Pri Phone #= ? Sec Phone #=...
  • Page 47 P100IH ISDN Router Field Description may enter any server set number up to 10, but the first one is used foe SUA only. Telco Transfer This field specifies the type of connection between the Prestige options: Type and this remote node. Select 64K, or Leased. Multilink The Prestige uses the PPP Multilink Protocol (PPP/MP) to bundle multiple links in a single connection to boost the effective...

  • Page 49: Chapter 4: Nat

    P100IH ISDN Router Chapter 4: Introduction NAT (Network Address Translation - NAT, RFC 1631) is the translation of an Internet Protocol address used within one network to a different IP address known within another network. One network is designated the inside network and the other is the outside.

  • Page 50: Figure 4-1 How Nat Works

    P100IH ISDN Router and Many-to-Many Overload NAT mapping) and then forwards each packet to the Internet ISP, thus making them appear as if they had come from the NAT system itself (e.g., the Prestige). The Prestige keeps track of the original addresses and port numbers so incoming reply packets can have their original values restored. The following diagram illustrates this.

  • Page 51: Nat Application

    P100IH ISDN Router Table 4-1 NAT Mapping Types Type IP Mapping One-to-One ILA1 IGA1 Many-to-One (SUA/PAT) ILA1 IGA1 ILA2 IGA1 … Many-to-Many Overload ILA1 IGA1 ILA2 IGA2 ILA3 IGA1 ILA4 IGA2 … Many-to-Many No Overload ILA1 IGA1 ILA2 IGA2 ILA3 IGA3 …...

  • Page 52: Sua (Single User Account) Versus Nat

    P100IH ISDN Router Figure 4-2 NAT Application SUA (Single User Account) Versus NAT SUA (Single User Account) in previous ZyNOS versions is a NAT set with 2 rules, Many-to-One and Server. See section 4.5.1 for a detailed description of the NAT set for SUA. The Prestige now has Full Feature NAT support to map global IP addresses to local IP addresses of clients or servers using all mapping types as outlined in Table 4-1 NAT Mapping Types.

  • Page 53: Smt Menus

    P100IH ISDN Router SMT Menus NAT Setup In The Main Menu Enter 15 from the main menu to configure NAT (this was SUA in previous versions). Prestige 100IH Main Menu Getting Started Advanced Management 1. General Setup 21. Filter Set Configuration 2.

  • Page 54: Figure 4-5 Applying Nat To The Remote Node

    P100IH ISDN Router Step 1. Enter 11 from the Main Menu. Step 2. Move the cursor to the Edit IP field, press the [SPACEBAR] to toggle the default No to Yes, then press [ENTER] to bring up Menu 11.3 - Remote Node Network Layer Options. Menu 11.3 - Remote Node Network Layer Options Rem IP Address= 172.16.1.20 IP Subnet Mask= 255.255.0.0...

  • Page 55: Configuring Nat

    P100IH ISDN Router Address A NAT Server Set is a list of LAN side servers mapped to external ports Mapping Set= (similar to the old SUA menu 15.1 before). You may enter any server set number up to 10, but the first one is used foe SUA only. Configuring NAT To configure NAT, enter 15 from the Main Menu to bring up the following screen.

  • Page 56: Figure 4-7 Menu 15.1 - Address Mapping Sets

    P100IH ISDN Router Menu 15.1 - Address Mapping Sets 1. Marc 255. SUA (read only) Enter Menu Selection Number: Figure 4-7 Menu 15.1 - Address Mapping Sets Let’s look first at Option 255. Option 255 is equivalent to SUA in previous ZyXEL routers (see section 4.2). The fields in this menu cannot be changed.

  • Page 57: Table 4-3 Sua Address Mapping Rules

    P100IH ISDN Router Table 4-3 SUA Address Mapping Rules Field Description Options/Example Set Name This is the name of the set you selected in Menu 15.1 or enter the name of a new set you want to create. This is the index or rule number. 0.0.0.0 Local Start IP This is the starting local IP address (ILA).
  • Page 58 P100IH ISDN Router Menu 15.1.1 - Address Mapping Rules Set Name= Marc Local Start IP Local End IP Global Start IP Global End IP Type --------------- --------------- --------------- --------------- ------ 0.0.0.0 255.255.255.255 0.0.0.0 Server Set= 1 0.0.0.0 Server Action= Edit Select Rule= Press ENTER to Confirm or ESC to Cancel: Figure 4-9 First Set in Menu 15.1.1...

  • Page 59: Figure 4-10 Editing The First Rule In A Set

    P100IH ISDN Router Field Description Option one will be advanced one rule. Save Set means to save the whole set (note when you choose this action, the Select Rule item will be disabled). Select Rule When you choose Edit, Insert Before or Delete in the previous field the cursor jumps to this field to allow you to select the rule to apply the action in question.

  • Page 60: Figure 4-11 Editing The Second Rule In A Set

    P100IH ISDN Router Menu 15.1.1.1 Marc - Rule 2 Type= Server Local IP: Start= N/A = N/A Global IP: Start= 0.0.0.0 = N/A Server Mapping Set= 1 Press ENTER to Confirm or ESC to Cancel: Figure 4-11 Editing The Second Rule in a Set The following table describes the fields in these screens.

  • Page 61: Figure 4-12 Multiple Servers Behind Nat

    P100IH ISDN Router Field Description Option/Example This field is N/A for One-to-One, Many-to- One and Server types. Note: For all Local and Global IPs, the End IP address must begin after the IP Start address, i.e., you cannot have an End IP address beginning before the Start IP address. 4.5.2 NAT Server Sets A NAT Server Set is a list of LAN side servers mapped to external ports (similar to the old SUA menu 15.1...

  • Page 62: Figure 4-13 Menu 15.2 - Nat Server Sets

    P100IH ISDN Router Configuring a Server behind NAT Follow the steps below to configure a server behind NAT: Step 1. Enter 15 in the main menu to go to Menu 15 – NAT Setup. Step 2. Enter 2 to go to Menu 15.2 - NAT Server Setup. Menu 15.2 - NAT Server Sets 1.

  • Page 63: Examples

    P100IH ISDN Router Step 5. Press [ENTER] at the “Press ENTER to confirm …” prompt to save your configuration after you define all the servers or press ESC at any time to cancel. The most often used port numbers are shown in the following table. Please refer to RFC 1700 for further information about port numbers.

  • Page 64: Figure 4-16 Internet Access & Nat Example

    P100IH ISDN Router Menu 4 - Internet Access Setup ISP's Name= ChangeMe Pri Phone #= 4125678 Sec Phone #= My Login= N/A My Password= N/A My WAN IP Addr= 0.0.0.0 NAT= SUA Only Address Mapping Set= 255 IP Subnet Mask= N/A Telco Options: Transfer Type= 64K Multilink= Off...

  • Page 65: Figure 4-18 Specifying An Inside Sever

    P100IH ISDN Router Menu 15.2.1 - Multiple Server Configuration Port # Address ---- --------------- 192.168.1.10 Default 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 6. 0 0.0.0.0 7. 0 0.0.0.0 8. 0 0.0.0.0 9. 0 0.0.0.0 10. 0 0.0.0.0 11. 0 0.0.0.0 12. 1025 RR Reserved Press ENTER to Confirm or ESC to Cancel: Figure 4-18 Specifying an Inside Sever...
  • Page 66 P100IH ISDN Router Figure 4-19 NAT - Example 3 In this case we need to configure Address Mapping Set 1 from Menu 15.1 - Address Mapping Sets. Therefore we must choose the Full Feature option from the Network Address Translation field in Menu 4 or Menu 11.3 and select an available NAT Server Set, say Server Set 2, that we configure later.

  • Page 67: Figure 4-20 Example 3 – Menu

    P100IH ISDN Router Menu 15.1.1.1 –Example3-Rule 1 Type= One-to-One Local IP: Start= 192.168.1.10 = N/A Global IP: Start= 10.132.50.1 = N/A Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 4-20 Example 3 – Menu 15.1.1.1 When we have configured all four rules, Menu 15.1.1 should look as follows.
  • Page 68 P100IH ISDN Router Step 8. Now enter 2 from this menu, enter 2 again to select Server Set 2 and configure it as shown in Figure 4-22. Menu 15.2.1 - Multiple Server Configuration Port # Address ---- --------------- 0.0.0.0 Default 2.80 192.168.1.21 3.25...

  • Page 69: Figure 4-24 Example 4- Menu

    P100IH ISDN Router Some applications still won’t work through NAT even when using types One-to-One and Many-to-Many No Overload mapping types. Follow the steps outlined in example 3 above to configure these two menus as follows. Menu 15.1.1.1 –Example4- Rule 1 Type= Many-to-Many No Overload Local IP: Start= 192.168.1.10...

  • Page 71: Chapter 5: Remote Node Configuration

    P100IH ISDN Router Remote Node Configuration Chapter 5: A remote node is required for placing calls to a remote gateway. A remote node represents both the remote gateway and the network behind it across a WAN connection. Note that when you use Menu 4 to set up Internet access, you are actually configuring one of the remote nodes.

  • Page 72: Figure 5-1 Menu 11 - Remote Node Setup

    P100IH ISDN Router Menu 11 - Remote Node Setup Menu 11 - Remote Node Setup 1. nodename 2. ________ 3. ________ 4. ________ 5. ________ 6. ________ 7. ________ 8. ________ Enter Node # to Edit: Figure 5-1 Menu 11 – Remote Node Setup When Submenu 11.1 - Remote Node Profile appears, fill in the fields as described in the table below to define this remote profile.

  • Page 73: Table 5-1 Remote Node Profile Menu Fields

    P100IH ISDN Router Table 5-1 Remote Node Profile Menu Fields Field Description Options Rem Node Name This is a required field [?]. Enter a descriptive name for the remote node, for example, Corp. This field can be up to eight characters. This name must be unique from any other remote node name or remote dial-in user name.
  • Page 74 P100IH ISDN Router This field is applicable only if Call Direction is Both. Enable Incoming: Callback Otherwise, a N/A appears in the field. Disable This field determines whether or not your Prestige will call back after receiving a call from this remote node. If this option is enabled, your Prestige will disconnect the initial call from this node and call it back at the Outgoing Primary Phone Number (see below).

  • Page 75: Outgoing Authentication Protocol

    P100IH ISDN Router Telco Options: Allocated Budget This field sets a ceiling for outgoing call time for this Default = 0 (min) remote node. The default for this field is 0 for no budget control. Transfer Type This field specifies the type of connection between the 64k/ Prestige and this remote node.

  • Page 76: Table 5-2 Btr V Mtr For Bod

    P100IH ISDN Router successful authentication, please make sure that you specify the correct authentication protocol when connecting to such an implementation. 5.1.4 PPP Multilink The Prestige uses the PPP Multilink Protocol (PPP/MP) to bundle multiple links in a single connection to boost the effective throughput between two nodes.

  • Page 77: Figure 5-3 Menu 11.2 - Remote Node Ppp Options

    P100IH ISDN Router outgoing traffic to make this determination and Receive will only use incoming traffic to make this determination. If, after making the call to bring up a second channel, the second channel does not succeed in joining the Multilink Protocol bundle (because the remote device does not recognize the second call as coming from the same device), the Prestige will hang up the second call and continue with the first channel alone.

  • Page 78: Table 5-3 Remote Node Ppp Options Menu Fields

    P100IH ISDN Router Table 5-3 Remote Node PPP Options Menu Fields Field Description Option Encapsulation Select the CISCO PPP only when this remote node Standard is a Cisco machine; otherwise, select the Standard PPP. CISCO Compression Turn on/off Stac Compression. The default for this On/Off field is Off.

  • Page 79: Figure 5-4 Menu 11.5 - Remote Node Filter

    P100IH ISDN Router 5.1.7 Remote Node Filter Use Menu 11.5 – Remote Node Filter to specify the filter set(s) to apply to the incoming and outgoing traffic between this remote node and the Prestige and to prevent certain packets from triggering calls. You can specify up to 4 filter sets separated by comma, e.g., 1, 5, 9, 12, in each filter field.

  • Page 81: Chapter 6: Remote Node Tcp/Ip Configuration

    P100IH ISDN Router Chapter 6: Remote Node TCP/IP Configuration This chapter shows you how to configure the TCP/IP parameters of a remote node. A typical LAN-to-LAN application is to use your Prestige to connect a branch office to the headquarters, as depicted in the following diagram.

  • Page 82: Figure 6-2 Menu 11.3- Remote Node Tcp/Ip Options

    P100IH ISDN Router 6.1.1 Remote Node Setup Follow the procedure below to configure the TCP/IP parameters in Menu 11 - Remote Node Profile. Follow the steps below to edit Menu 11.3 - Remote Node Network Layer Options shown below. Move the cursor to the Edit IP field, then press the space bar to toggle and set the value to Yes. Press [Enter] to open Menu 11.3 - Network Layer Options.

  • Page 83: Figure 6-3 Sample Ip Addresses For A Tcpi/Ip Lan-To-Lan Connection

    P100IH ISDN Router Figure 6-3 Sample IP Addresses for a TCPI/IP LAN-to-LAN Connection To configure the TCP/IP parameters of a remote node, first configure the two fields in Menu 11 – Remote Node Profile, as shown in the table below. Table 6-1 TCP/IP related fields in Remote Node Profile Field Description...

  • Page 84: Table 6-2 Tcp/Ip Remote Node Configuration

    P100IH ISDN Router Table 6-2 TCP/IP Remote Node Configuration Rem IP Address This will show the IP address you entered for this remote node in the previous menu. Rem IP Subnet Enter the subnet mask for the remote network. Mask Some implementations, especially the UNIX derivatives, require the My WAN Addr WAN link to have a separate IP network number from the LAN and...

  • Page 85: Figure 6-4 Example Of Static Routing Topology

    P100IH ISDN Router Once you have completed filling in the Network Layer Options Menu, press [Enter] to return to Menu 11. Press [Enter] at the message [Press ENTER to Confirm...] to save your configuration, or press [Esc] at any time to cancel. 6.1.2 Static Route Setup Static routes tell the Prestige routing information that it cannot learn automatically through other means.

  • Page 86: Figure 6-5 Menu 12.1 - Ip Static Route Setup

    P100IH ISDN Router Menu 12 - IP Static Route Setup 1. ________ 2. ________ 3. ________ 4. ________ 5. ________ 6. ________ 7. ________ 8. ________ Enter selection number: Figure 6-5 Menu 12.1 - IP Static Route Setup Choosing a static route to edit produces the following screen. Menu 12.1 - Edit IP Static Route Route #: 1 Route Name= ?

  • Page 87: Table 6-3 Edit Ip Static Route Menu Fields

    P100IH ISDN Router The following table describes the fields for Menu 12.1.1 – Edit IP Static Route Setup. Table 6-3 Edit IP Static Route Menu Fields Field Description Route Name Enter a descriptive name for this route. This is for identification purpose only. Active This field allows you to activate/deactivate this static route.

  • Page 89: Chapter 7: Dial-In Server Configuration

    P100IH ISDN Router Chapter 7: Dial-in Server Configuration You can configure your Prestige to receive calls from remote dial-in users, e.g., telecommuters, as well as remote nodes. There are several differences between dial-in users and remote nodes, as summarized in the table below.

  • Page 90: Remote Access Server

    P100IH ISDN Router Remote Access Server Telecommuting enables people to work at remote sites and yet still have access to the resources in the business office. Typically, a telecommuter will use a client workstation with TCP/IP and dial-out capabilities, e.g., a Windows PC or a Macintosh. For telecommuters to call in to your Prestige, you need to configure a dial-in user profile for each telecommuter.

  • Page 91: Default Dial-In Setup

    P100IH ISDN Router Figure 7-2 Example of a LAN-to-LAN Server Application Default Dial-In Setup This section covers the default dial-in parameters. The parameters in Menu 13 affect incoming calls from both remote dial-in users, and remote nodes until authentication is completed. Once authentication is completed and if it matches a remote node, your Prestige will use parameters from that particular remote node.

  • Page 92: Figure 7-3 Menu 13 - Default Dial-In Setup

    P100IH ISDN Router Menu 13 - Default Dial-in Setup Telco Options: IP Address Supplied By: CLID Authen= None Dial-in User= Yes IP Pool= No PPP Options: IP Start Addr= N/A Recv Authen= CHAP/PAP IP Count(1,2)= N/A Compression= Yes Mutual Authen= No O/G Login= p100ih O/G Password= ******** Multiple Link Options:...
  • Page 93 P100IH ISDN Router Recv. Authen This field sets the authentication protocol for incoming calls. For security reason, setting authentication to none is strongly discouraged. Options for this field are: CHAP/PAP - Your Prestige will try CHAP first, but CHAP/PAP PAP will be used if CHAP is not available. CHAP CHAP –...
  • Page 94 P100IH ISDN Router IP Address Supplied By: If set to Yes, the Prestige will allow a remote host to (Default = Yes) Dial-in User specify its own IP address. Yes/No If set to No, the remote host must use the IP address assigned by your Prestige from the IP pool, configured below.

  • Page 95: Dial-In Users Setup

    P100IH ISDN Router but not the remote nodes. You can specify up to 4 filter sets separated by comma, e.g., 1, 5, 9, 12, in each filter field. The default is no filters. Spaces are accepted in this field. For more information on defining the filters, see Chapter 9: . Menu 13.1 - Default Dial-in Filter Input Filter Sets: protocol filters=...

  • Page 96: Figure 7-5 Menu 14 - Dial-In User Setup

    P100IH ISDN Router Menu 14 - Dial-in User Setup 1. johndoe 2. ________ 3. ________ 4. ________ 5. ________ 6. ________ 7. ________ 8. ________ Enter Menu Selection Number: Figure 7-5 Menu 14 - Dial-in User Setup Step 2. Select one of the users by number, this will bring you to Menu 14.1 - Edit Dial-in User, as shown below.

  • Page 97: Table 7-3 Edit Dial-In User Menu Fields

    P100IH ISDN Router The following table provides instructions on how to fill in the Edit Dial-In User fields. Table 7-3 Edit Dial-in User Menu Fields Field Description Option User This is a required field. This will be used as the login name for authentication. Name Choose a descriptive word for login, for example, [johndoe].

  • Page 98: Table 7-4 Edit Dial-In User Menu Fields (Continued)

    P100IH ISDN Router Table 7-4 Edit Dial-in User Menu Fields (continued) Field Description Option Rem CLID If you enable CLID Authen field in Menu 13, then you need to specify the telephone number from which this user calls. Your Prestige will check the CLID in the incoming call against the CLIDs in the database.

  • Page 99: Chapter 8: Advanced Phone Services

    P100IH ISDN Router Chapter 8: Advanced Phone Services The Prestige 100 and 100IH support a comprehensive set of advanced calling features known as Supplemental Services. European and North American ISDN Supplemental Services may vary and have different naming conventions that can be generalized as follows. Please check with your telephone company for the services it offers.

  • Page 100: Getting Started

    P100IH ISDN Router Table 8-2 Supplemental Services by switch type. Feature: DSS-1 1TR6 × Call Waiting/Call Hold/Call Retrieve × Three Way Calling (Conference/Transfer/Drop) × Call Forwarding × × Reminder Ring Getting Started 8.1.1 Things you need to know before you start using Supplemental Services.

  • Page 101: Call Waiting

    P100IH ISDN Router effect. However, using the flash key is preferred since the timing is much more precise. With manually tapping, if the duration is too long, it may be interpreted as hanging up by the Prestige. Call Waiting ISDN Call Waiting allows you to place a call on hold while you answer another incoming call on the same telephone (directory) number.

  • Page 102: Call Transfer

    P100IH ISDN Router Note: If you wish to cancel your attempt to establish the conference call because the third party’s line in busy or if they don't answer, simply hang-up the telephone and pick it back up after it starts ringing to return to the first caller.

  • Page 103: Reminder Ring

    P100IH ISDN Router There are two methods to activate call forwarding. The first is exactly the same as on an analog line, i.e., you pick up the handset and dial the access code assigned by your telephone company and the number that you want the calls forwarded.

  • Page 105: Chapter 9: Filter Configuration

    P100IH ISDN Router Chapter 9: Filter Configuration About Filtering Your Prestige uses filters to decide whether or not to allow passage of a data packet and/or to make a call. There are two types of filters: data filters and call filters. Data filters screen the data to determine if the packet should be allowed to pass.

  • Page 106: Figure 9-1 Filter Rule Process

    P100IH ISDN Router Start Packet into Filter Fetch First Filter Set Filter Set Fetch Next Fetch First Filter Set Filter Rule Y e s Fetch Next Y e s Filter Rule Execute Filter Next Filter Set Next Filter Rule Available? Available? R u l e C h e c k N e x t R u l e...

  • Page 107: The Filter Structure Of The Prestige

    P100IH ISDN Router Call Filters Active Data Built-in User-defined Data match match match Outgoing Initiate call default Call Filters Filters Packet if line not up Call Filters (if applicable) Send packet and reset Idle Timer Match Match Match Drop Drop packet Drop packet packet if line not up...

  • Page 108: Configuring A Filter Set

    P100IH ISDN Router Configuring a Filter Set To configure a filter sets, follow the procedure below: Step 1. Select option 21. Filter Set Configuration from the Main Menu to open Menu 21. Menu 21 - Filter Set Configuration Filter Filter Set # Comments Set #...

  • Page 109: Figure 9-4 Menu 21.1 - Filter Rules Summary

    P100IH ISDN Router Menu 21.1 - Filter Rules Summary # A Type Filter Rules M m n - - ---- -------------------------------------------- --------- - - - 1 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=137 N D N 2 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=138 N D N 3 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=139...

  • Page 110: Table 9-2 Abbreviations Used If Filter Type Is Ip

    P100IH ISDN Router Abbreviations Description Display Type Refers to the type of filter rule. [GEN] for Generic This shows GEN for generic, IP for [IP] for TCP/IP TCP/IP Filter Rules The filter rule parameters will be displayed here (see below). Refers to More.

  • Page 111: Configuring A Filter Rule

    P100IH ISDN Router Abbreviation Description Source Port number Destination Address Destination Port number If the filter type is GEN (generic), the following abbreviations listed in the following table will be used. Table 9-3 Abbreviations Used If Filter Type Is GEN Abbreviation Description Offset...

  • Page 112: Figure 9-6 Protocol And Device Filter Sets

    P100IH ISDN Router Figure 9-6 Protocol and Device Filter Sets To speed up filtering, all rules in a filter set must be of the same class, i.e., protocol filters or generic filters. The class of a filter set is determined by the first rule that you create. When applying the filter sets to a port, separate menu fields are provided for protocol and device filter sets.

  • Page 113: Figure 9-7 Menu 21.1.1 - Tcp/Ip Filter Rule

    P100IH ISDN Router Menu 21.1.1 - TCP/IP Filter Rule Filter #: 1,1 Filter Type= TCP/IP Filter Rule Active= Yes IP Protocol= 6 IP Source Route= No Destination: IP Addr= 0.0.0.0 IP Mask= 0.0.0.0 Port #= 137 Port # Comp= Equal Source: IP Addr= 0.0.0.0 IP Mask= 0.0.0.0 Port #= 0...
  • Page 114 P100IH ISDN Router Field Description Option filter. The range of this field is 0 to 65535. This field is a don’t-care if it is 0. None/Less/Greater/ Destination: Port # Select the comparison to apply to the destination port in Equal/Not Equal Comp the packet against the value given in Destination: Port #.
  • Page 115 P100IH ISDN Router Field Description Option Forward Drop Once you have completed filling in Menu 21.1.1 - TCP/IP Filter Rule, press [Enter] at the message [Press Enter to Confirm] to save your configuration, or press [Esc] to cancel. This data will now be displayed on Menu 21.1 - Filter Rules Summary.

  • Page 116: Figure 9-8 Executing An Ip Filter

    P100IH ISDN Router Packet into IP Filter Filter Active? Y e s A p p l y S r c A d d r M a s k to Src Addr Check Src N o t M a t c h e d IP Addr M a t c h e d A p p l y D e s t A d d r M a s k...

  • Page 117: Figure 9-9 Menu 21.1.2 - Generic Filter Rule

    P100IH ISDN Router 9.3.3 Generic Filter Rule This section shows you how to configure a generic filter rule. The purpose of generic rules is to allow you to filter non-IP packets. For IP, it is generally easier to use the IP rules directly. For generic rules, the Prestige treats a packet as a byte stream as opposed to an IP or IPX packet.

  • Page 118: Table 9-5 Generic Filter Rule Menu Fields

    P100IH ISDN Router The table below describes the fields in the Generic Filter Rule Menu. Table 9-5 Generic Filter Rule Menu Fields Field Description Option Filter # This is the filter set, filter rule co-ordinates, i.e., 2,3 refers to the second filter set and the third rule of that set.

  • Page 119: Applying A Filter And Factory Defaults

    P100IH ISDN Router Field Description Option Select the action for a packet not matching the rule. Check Next Action Not Rule Matched Forward Drop Once you have completed filling in Menu 21.1.2 - generic Filter Rule, press [Enter] at the message [Press Enter to Confirm] to save your configuration, or press [Esc] to cancel.

  • Page 120: Remote Node Filters

    P100IH ISDN Router 9.4.2 Remote Node Filters Go to Menu 11.5 (shown below) and enter the number(s) of the filter set(s) as appropriate. You can cascade up to four filter sets by entering their numbers separated by commas. The factory default filter set, NetBIOS_WAN, is inserted in protocol filters field under Call Filter Sets in Menu 11.5 to block local NetBIOS traffic from triggering calls to the remote node.

  • Page 121: Chapter 10: Telnet Configuration And Capabilities

    P100IH ISDN Router Chapter 10: Telnet Configuration and Capabilities 10.1 About Telnet Configuration Before the Prestige is properly setup for TCP/IP, the only option for configuring it is through the console port. Once your Prestige is configured, you can use telnet to configure it remotely as shown below. Figure 10-1 Telnet Configuration on a TCP/IP Network 10.2 Telnet Under NAT When NAT is enabled and an inside telnet server is specified, telnet connections from the outside will be...

  • Page 122: System Timeout

    P100IH ISDN Router 10.3 Telnet Capabilities 10.3.1 Single Administrator To prevent confusion and discrepancy on the configuration, your Prestige only allows one administrator to log in at any time. Your Prestige also gives priority to the console port over telnet. If you have already connected to your Prestige via telnet, you will be logged out if another user logs in to the Prestige via the console port.

  • Page 123: Chapter 11: System Maintenance

    P100IH ISDN Router Chapter 11: System Maintenance This chapter covers the diagnostic tools that help you to maintain your Prestige. These tools include updates on system status, port status, log and trace capabilities and upgrades for the system software. This chapter describes how to use these tools in detail.

  • Page 124: 11.1 System Status

    P100IH ISDN Router 11.1 System Status The first selection, System Status, gives you information on the status and statistics of the ports, as shown below. System Status is a tool that can be used to monitor your Prestige. Specifically, it gives you information on your ISDN telephone line status, number of packets sent and number of packets received.
  • Page 125 P100IH ISDN Router Field Description The current connecting speed (56K or 64K). Type TXPkt The number of transmitted packets on this channel. RXPkt The number of received packets on this channel. Error The number of error packets on this channel. (Current Line Utilization) percentage of current bandwidth used on this channel (Average Line Utilization) a 5-second moving average of channel...

  • Page 126: System Information

    P100IH ISDN Router Field Description LAN Packet Which Shows the first 48 octets of the LAN packet that triggered the last Triggered Last Call outgoing call. LAN Packet Which Triggered Last Call: (Type IP) 45 00 00 3C 02 12 00 00 3B 01 36 49 00 00 00 00 C0 44 87 22 08 00 62 2B 20 04 00 00 00 08 A9 D0 C0 44 87 22 00 01 02 03 04 05 06 07 08 09 0A 0B Source IP Address Source MAC Address...

  • Page 127: Figure 11-4 System Maintenance - Information

    P100IH ISDN Router Menu 24.2.1 – System Maintenance - Information Name: Routing: IP RAS S/W Version: V2.41(G.00) | 1/18/2000 ISDN F/W Version: V 09D Country Code: 225 Ethernet Address:00:a0:c5:02:34:56 IP Address: 192.168.1.1 IP Mask: 255.255.255.0 DHCP: Server Press ESC or RETURN to Exit: Figure 11-4 System Maintenance - Information Table 11-2 Fields in System Maintenance Field...

  • Page 128: 11.2 Log And Trace

    P100IH ISDN Router 11.1.2 Console Port Speed You can set up different port speeds for the console port through Menu 24.2.2 – Console Port Speed. Your Prestige supports 9600 (default), 19200, 38400, 57600, and 115200bps for the console port. Use the space bar to select the desired speed in Menu 24.2.2, as shown in the following figure.

  • Page 129: Figure 11-6 Examples Of Error And Information Messages

    P100IH ISDN Router Examples of typical error and information messages are presented in the figure below. 4 PP07 INFO LAN promiscuous mode <0> 4 PINI ERROR System Ert completed e PINI INFO Session Begin Clear Error Log (y/n): Figure 11-6 Examples of Error and Information Messages 11.2.2 Syslog And Accounting The Prestige uses the UNIX syslog facility to log the CDR (Call Detail Record) and system messages to a...

  • Page 130: Table 11-3 System Maintenance Menu Syslog Parameters

    P100IH ISDN Router Table 11-3 System Maintenance Menu Syslog Parameters Parameter Description Active Use the space bar to turn on or off syslog. Syslog IP Address Enter the IP Address of your syslog server. Log Facility Use the space bar to toggle between the 7 different Local options. The log facility allows you to log the message in different files in the server.

  • Page 131: 11.3 Diagnostic

    P100IH ISDN Router 11.3 Diagnostic The diagnostic facility allows you to test the different aspects of your Prestige to determine if it is working properly. Menu 24.4 allows you to choose among various types of diagnostic tests to evaluate your system, as shown below.

  • Page 132: Table 11-4 System Maintenance Menu Diagnostic

    P100IH ISDN Router The following table describes the diagnostic tests available in Menu 24.4 for your Prestige and the connections. Table 11-4 System Maintenance Menu Diagnostic Field Description Hang Up B1 Call This command hangs up the B1 channel. This is only applicable if the B1 channel is currently in use.

  • Page 133: Figure 11-9 Display For A Successful Manual Call

    P100IH ISDN Router Start dialing for node <1> ### Hit any key to continue. ### Dialing chan<2> phone<last 9-digit>:12345 Call CONNECT speed<64000> chan<2> prot<1> LCP up CHAP send response CHAP login to remote OK! IPCP negotiation started IPCP up Figure 11-9 Display for a Successful Manual Call This figure shows an example where authentication failed.

  • Page 134: 11.4 Backup Configuration

    P100IH ISDN Router 11.4 Backup Configuration Option 5 from Menu 24 - System Maintenance allows you to backup the current Prestige configuration to your workstation. Backup is highly recommended once your Prestige is functioning properly. You must perform the backup and restore through the console port. Any serial communications program should work fine;...

  • Page 135: 11.5 Restore Configuration

    P100IH ISDN Router ** Backup Configuration completed. OK. ### Hit any key to continue.### Figure 11-13 Successful Backup 11.5 Restore Configuration Select option 6 from Menu 24 - System Maintenance to restore the configuration from your workstation to the Prestige. Again, you must use the console port and XMODEM protocol to restore the configuration. Rest assured that the configuration is stored in the flash ROM in the Prestige, so even if power failure should occur, your configuration is safe.

  • Page 136: 11.6 Firmware Upload

    P100IH ISDN Router Step 5. After a successful restoration you will see the following screen. Press any key to return to reboot the system. Save to ROM Hit any key to start system reboot. Figure 11-16 Successful Restoration Keep in mind that the configuration is stored in the flash ROM in the Prestige, so even if power failure should occur, your configuration is safe.

  • Page 137: Figure 11-18 Menu 24.7.1 - Uploading Router Firmware

    P100IH ISDN Router Step 3. After successful firmware upload, enter “atgo” to restart the Prestige. Menu 24.7.1 -- System Maintenance - Upload Router Firmware To upload router firmware: 1. Enter "y" at the prompt below to go into debug mode. 2.

  • Page 138: Figure 11-19 Menu 24.7.2 - System Maintenance - Upload Router Configuration File

    P100IH ISDN Router Menu 24.7.2 - System Maintenance - Upload Router Configuration File To upload router configuration file: 1. Enter "y" at the prompt below to go into debug mode. 2. Enter "atur3" after "Enter Debug Mode" message. 3. Wait for "Starting XMODEM upload" message before activating Xmodem upload on your terminal.

  • Page 139: Figure 11-20 Tftp Example

    P100IH ISDN Router If you upload the firmware to the Prestige, it will reboot automatically when the file transfer is completed (the SYS LED will flash). Note that the telnet connection must be active and the SMT in CI mode before and during the TFTP transfer.

  • Page 140: Figure 11-21 Boot Module Commands

    P100IH ISDN Router ======= Debug Command Listing ======= ATHE print help ATGO boot system ATUR upload RAS code ATUR3 upload RAS configuration file ATBAx change baud rate. 1:38.4,2:19.2,3:9.6,4:57.6,5:115.2 ATTD download configuration to PC ATSE display seed for password generation ATSH display Revision and etc Figure 11-21 Boot module commands 11-18...

  • Page 141: 11.7 Command Interpreter Mode

    [help] at the command prompt. For more detailed information, check the ZyXEL Web site or send e- mail to the ZyXEL Support Group. Enter Menu Selection Number: 8 Copyright (c) 1994 - 2000 ZyXEL Communications Corp. ras> ? Valid commands are:...

  • Page 142: Figure 11-23 Menu 24.9 - System Maintenance - Call Control

    P100IH ISDN Router To enter the call control menu, select option 9. Call Control in Menu 24 to go to Menu 24.9 - System Maintenance - Call Control, as shown in the table below. Menu 24.9 - System Maintenance - Call Control Call Control Parameters Blacklist Budget Management...

  • Page 143: Figure 11-25 Menu 24.9.2 - Blacklist

    P100IH ISDN Router 11.8.2 Blacklist The phone numbers on the blacklist are numbers that the Prestige had problems connecting in the past. The only operation allowed is for you to take a number off the list by entering its index number. Menu 24.9.2 shows the list of telephone numbers that have been blacklisted.

  • Page 144: Figure 11-26 Menu 24.9.3 - Budget Management

    P100IH ISDN Router 11.8.3 Budget Management Menu 24.9.3 shows the budget management statistics for outgoing calls. Menu 24.9.3 - Budget Management Remote Node Connection Time/Total Budget Elapsed Time/Total Period 1. isp1 No Budget No Budget 2. -------- 3. -------- 4. -------- 5.

  • Page 145: 11.9 Time And Date Setting

    P100IH ISDN Router 11.8.4 Call History This is the fourth option in Call Control and relays information about past incoming and outgoing calls. Menu 24.9.4 - Call History Phone Number Rate #call Total Enter Entry to Delete(0 to exit): Figure 11-27 Call History Table 11-6 Call History Fields Field Description...

  • Page 146: Figure 11-28 System Maintenance - Time And Date Setting

    P100IH ISDN Router get the current time and date from an external server when you power up your Prestige. Go to Menu 24.10 to update the time and date settings of your Prestige. Menu 24.10 - System Maintenance - Time and Date Setting Use Time Server when Bootup= None Time Server IP Address= N/A Current Time:...

  • Page 147: Table 11-7 Time And Date Setting Fields

    P100IH ISDN Router Table 11-7 Time and Date Setting Fields Field Description Use Time Server when Enter the time service protocol that your timeserver will send when the Prestige powers up. Choices are Daytime (RFC 867), Time (RFC-868), Bootup= NTP (RFC-1305) and None. The main differences between them are the format, e.g., the Daytime (RFC 867) format is day/month/date/year/time zone of the server while the Time (RFC-868) format gives a 4-byte integer giving the total number of seconds since 1/1/1970 at 0:0:0.

  • Page 149: Chapter 12: Call Scheduling

    You can apply up to 4 schedule sets in Menu 11.1 - Remote Node Profile. You configure each schedule in Menu 26 - Schedule Setup. Copyright (c) 1994 – 1999 ZyXEL Communications Corp. Prestige 100IH Main Menu...

  • Page 150: Figure 12-3 Schedule Set Setup

    P100IH ISDN Router take precedence over set 2, 3 and 4 as it is applied first. Set 2 will take precedence over set 3 and 4, and so You can design up to 12 schedule sets but you can only apply up to 4 schedule sets for a remote node. To delete a schedule set, enter the set number and press the [Space Bar] (or delete) in the Edit Name field to delete the set name.

  • Page 151: Table 12-1 Schedule Set Setup Fields

    P100IH ISDN Router Table 12-1 Schedule Set Setup Fields Field Description Option Active Press the [Space Bar] to toggle between Yes and No. Choose Yes and press [Enter] to activate the set. Start Date Enter the start date that you wish the set to take effect in year-month- date format.
  • Page 152 P100IH ISDN Router Menu 11.1 - Remote Node Profile Rem Node Name= ? Edit PPP Options= No Active= Yes Rem IP Addr= ? Call Direction= Both Edit IP= No Incoming: Telco Option: Rem Login= ? Transfer Type= 64K Rem Password= ? Allocated Budget(min)= Rem CLID= Period(hr)=...

  • Page 153: Chapter 13: Troubleshooting

    P100IH ISDN Router Chapter 13: Troubleshooting This chapter covers the potential problems you may run into and the possible remedies. After each problem description, some instructions are provided to help you to diagnose and to solve the problem. 13.1 Problems Starting Up the Prestige Table 13-1 Troubleshooting the Start-Up of your Prestige Problem Corrective Action...

  • Page 154: 13.2 Problems With The Isdn Line

    P100IH ISDN Router 13.2 Problems With the ISDN Line Table 13-2 Troubleshooting the ISDN Line Problem Corrective Action Check the error log (in menu 24.3.1), you should see a log entry for The ISDN initialization failed. This problem occurs when you the ISDN initialization failure in the format, ‘ISDN init failed.

  • Page 155: 13.3 Problems With The Lan Interface

    P100IH ISDN Router 13.3 Problems with the LAN Interface Table 13-3 Troubleshooting the LAN Interface Problem Corrective Action Can’t ping any station on the LAN Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a station connected. If it is off, check the cables between your Prestige and the station.

  • Page 157: Appendix

    P100IH ISDN Router Appendix Acronyms and Abbreviations Attachment Unit Interface BAP/BACP Bandwidth Allocation Protocol/Bandwidth Allocation Control protocol Bandwidth on Demand Call Detail Record CHAP Challenge Handshake Authentication Protocol CLID Calling Line IDentification CSU/DSU Channel Service Unit/Data Service Unit Data Communications Equipment DOVBS Data Over Voice Bearer Service DHCP...
  • Page 158 P100IH ISDN Router POTS Plain Old Telephone Service Point to Point Protocol PSTN Public Switched Telephone Network Request For Comment Routing Information Protocol (IPX) Service Advertising Protocol SNMP Simple Network Management Protocol Single User Account (ISDN) Terminal Adapter TFTP Trivial File Transfer Protocol Transmission Control Protocol User Datagram Protocol Unshielded Twisted Pair (cable)

  • Page 159: Index

    P100IH ISDN Router Index authentication, 5-4, 5-5, 7-4 DNS, 3-3, 3-5 backup, 11-12 Domain Name, 4-24 BACP, 5-6 encapsulation, 5-8 Bandwidth on Demand. See BOD Ethernet, 2-13 BAP, 5-6 Filename Conventions, 2-7 Base Transmission Rate, 5-6 filter, 2-14, 5-9, 7-7, 9-1, 9-16 blacklist, 11-21 Filters BOD, 5-6...
  • Page 160 P100IH ISDN Router location, 2-9 RAS code, 11-14 log, 11-6 remote node, 5-1, 7-1 login, 5-3 Remote Node, 5-8, 11-2, 11-3, 11-10 Main Menu, 2-6 Resetting the Prestige, 2-8 Max. Transmission Rate, 5-6 restore, 11-13 metric, 6-4, 6-7 RIP, 3-2, 3-6, 6-4 MP, 2, 3-9, 5-6 Server, 1, 3-8, 4-11, 4-12, 4-15, 4-16, 4-18, 4-21, 4-22, 4-22, 4-23, 4-25, 4-26, 6-4, 11-25...

Table of Contents