Cisco Power system Installation Manual
Cisco Power system Installation Manual

Cisco Power system Installation Manual

Redundant power system
Table of Contents

Advertisement

Quick Links

Cisco Redundant Power System
Hardware Installation Guide
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel:
408 526-4000
800 553-NETS (6387)
Fax:
408 526-4100
Text Part Number: OL-3654-01

Advertisement

Table of Contents
loading

Summary of Contents for Cisco Power system

  • Page 1 Cisco Redundant Power System Hardware Installation Guide Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-3654-01...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
  • Page 3 Breakthrough, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and Voice LAN are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, The Fastest Way to Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.;...
  • Page 5: Table Of Contents

    Overview C H A P T E R Features Supported Devices and Configurations Quasi-Redundant Configuration Fully Redundant Configuration Redundant with Reboot Quasi- and Fully Redundant Mixed Configuration Front and Rear Panel Descriptions Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 6 C H A P T E R Power Considerations Connecting Hubs Connecting Switches Connecting Routers and the Cisco MC3810 Concentrator 4-13 Troubleshooting the Cisco RPS C H A P T E R Reading the LEDs Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 7 Contents Displaying Status Error Messages on Cisco 2600 Series and Cisco 3620, Cisco 3640, and Cisco 3725 Routers DC Failure AC Failure Fan Failure Temperature Error 5-10 Multiple Errors 5-12 Replacing an External Device 5-13 Getting Technical Support 5-14 Technical Specifications...
  • Page 8 Contents Cisco Redundant Power System Hardware Installation Guide viii OL-3654-01...
  • Page 9: Preface

    If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.
  • Page 10: Audience

    This publication is designed for people who have some experience installing networking equipment such as routers, hubs, servers, and switches. We assume that the person installing and troubleshooting the Cisco RPS is familiar with electronic circuitry and wiring practices and has experience as an electronic or electromechanical technician.
  • Page 11: Related Publications

    Note: This documentation is to be used in conjunction with the specific product installation guide that shipped with the product. Please refer to the Installation Guide, Configuration Guide, or other enclosed additional documentation for further details. Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 12 Tässä asiakirjassa esitettyjen varoitusten käännökset löydät laitteen mukana toimitetuista ohjeista. Huomautus SÄILYTÄ NÄMÄ OHJEET Huomautus Tämä asiakirja on tarkoitettu käytettäväksi yhdessä tuotteen mukana tulleen asennusoppaan kanssa. Katso lisätietoja asennusoppaasta, kokoonpano-oppaasta ja muista mukana toimitetuista asiakirjoista. Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 13 Hinweis Dieses Handbuch ist zum Gebrauch in Verbindung mit dem Installationshandbuch für Ihr Gerät bestimmt, das dem Gerät beiliegt. Entnehmen Sie bitte alle weiteren Informationen dem Handbuch (Installations- oder Konfigurationshandbuch o. Ä.) für Ihr spezifisches Gerät. Cisco Redundant Power System Hardware Installation Guide xiii OL-3654-01...
  • Page 14 Nota CONSERVARE QUESTE ISTRUZIONI Nota La presente documentazione va usata congiuntamente alla guida di installazione specifica spedita con il prodotto. Per maggiori informazioni, consultare la Guida all'installazione, la Guida alla configurazione o altra documentazione acclusa. Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 15 Nota Esta documentação destina-se a ser utilizada em conjunto com o manual de instalação incluído com o produto específico. Consulte o manual de instalação, o manual de configuração ou outra documentação adicional inclusa, para obter mais informações. Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 16 översatta säkerhetsvarningarna som medföljer denna anordning. OBS! SPARA DESSA ANVISNINGAR OBS! Denna dokumentation ska användas i samband med den specifika produktinstallationshandbok som medföljde produkten. Se installationshandboken, konfigurationshandboken eller annan bifogad ytterligare dokumentation för närmare detaljer. Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 17 Preface Notes, Cautions, and Warnings Cisco Redundant Power System Hardware Installation Guide xvii OL-3654-01...
  • Page 18: Obtaining Documentation

    Obtaining Documentation Obtaining Documentation These sections explain how to obtain documentation from Cisco Systems. World Wide Web You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com Translated documentation is available at this URL: http://www.cisco.com/public/countries_languages.shtml...
  • Page 19: Documentation Feedback

    Cisco Technical Assistance Center (TAC) Web Site. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC Web Site. Cisco.com Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world.
  • Page 20: Technical Assistance Center

    Cisco TAC Web Site You can use the Cisco TAC Web Site to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software.
  • Page 21: Cisco Tac Escalation Center

    If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco TAC Web Site, you can open a case online by using the TAC Case Open tool at this URL: http://www.cisco.com/tac/caseopen If you have Internet access, we recommend that you open P3 and P4 cases through the Cisco TAC Web Site.
  • Page 22 Preface Obtaining Technical Assistance Cisco Redundant Power System Hardware Installation Guide xxii OL-3654-01...
  • Page 23: Overview

    The Cisco RPS supports quasi-redundant, fully redundant, or redundant-with-reboot configurations, depending upon the external device. This chapter provides an overview of the Cisco RPS features, including the supported external devices and power configurations, in the following sections: •...
  • Page 24: Supported Devices And Configurations

    Simple Network Management Protocol (SNMP) support of error messages • for Cisco 2600 series and Cisco 3620/3640 series routers. (There is no SNMP support for error messages in the Cisco 1516M hub, FastHub 400 series hub, Catalyst 1900 series switches, Catalyst 2820 series switches, Catalyst 2900 and Catalyst 3500 series XL switches, Cisco 2500 and 4000 series routers, and the Cisco MC3810 multiservice concentrator.)
  • Page 25 3. The Cisco RPS can also be used with the older FastHub 100, 200, and 300 series hubs. 4. If you are using a Cisco RPS with a revision level lower than Z3 with a Catalyst 3508G or a Catalyst 3548 XL switch, the switch RPS LED and the RPS DC LED might display amber (normally indicating RPS malfunction) even when the Cisco RPS is functioning properly.
  • Page 26: Quasi-Redundant Configuration

    1-1. The power source is quasi-redundant because there are two AC input power modules for the Cisco RPS and one DC output power module for each external device. The AC input to the Cisco RPS is fully redundant, but the DC output to the external devices is not.
  • Page 27: Fully Redundant Configuration

    Supported Devices and Configurations Fully Redundant Configuration The Cisco RPS can provide a fully redundant power source for two of the supported routers or concentrators. You can use a two-to-one cable (ordered separately) to connect two external devices to the four DC output power modules,...
  • Page 28: Redundant With Reboot

    Redundant with Reboot By using a mode of operation called redundant with reboot, you can connect more hubs and switches to the Cisco RPS and thereby extend its capacity or provide additional redundancy. Redundancy with reboot works for the following devices only: FastHub 400 series hubs, Catalyst 1900 series and Catalyst 2820 switches, and Catalyst 2900 series and Catalyst 3500 series XL switches.
  • Page 29: Quasi- And Fully Redundant Mixed Configuration

    Cisco RPS to ensure correct operation. If the Cisco RPS powers up first, the LEDs might not indicate the actual state. After power up, a sense circuit in the Cisco RPS reads that the device has its AC power connected and shuts the Cisco RPS output off, preventing competition between the power supplies.
  • Page 30: Front And Rear Panel Descriptions

    DC output Fully redundant Quasi-Redundant Front and Rear Panel Descriptions The LEDs on the Cisco RPS front panel show the Cisco RPS operational status. Figure 1-5 shows the front panel of the Cisco RPS. Figure 1-5 Cisco RPS Front Panel...
  • Page 31: Leds

    FAN and TEMP LEDs—Both on the right side of the front panel. • When the Cisco RPS is working properly, all LEDs on its front panel are solid green. Some external devices also include LEDs that show the operating condition of the Note Cisco RPS.
  • Page 32 LED Name Color/State Description AC STATUS Off AC power is not being supplied to the Cisco RPS, or it is switched off. Amber AC power is being supplied to the Cisco RPS, but the designated AC-input power module has failed.
  • Page 33: Safety Recommendations

    If you are using a Cisco RPS with a revision level lower than Z3 Note with a Catalyst 3508G or a Catalyst 3548 XL switch, the switch...
  • Page 34: Safety Warnings

    To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device. Cisco Redundant Power System Hardware Installation Guide 1-12 OL-3654-01...
  • Page 35 If possible, send another person to get medical aid. Otherwise, determine – the condition of the victim and then call for help. Determine if the person needs rescue breathing or external cardiac – compressions; then take appropriate action. Cisco Redundant Power System Hardware Installation Guide 1-13 OL-3654-01...
  • Page 36 Chapter 1 Overview Safety Recommendations Cisco Redundant Power System Hardware Installation Guide 1-14 OL-3654-01...
  • Page 37: Chapter 2 Installing The Cisco Rps

    C H A P T E R Installing the Cisco RPS You can set the Cisco RPS chassis on a desktop or install it in a rack. Only trained and qualified personnel should be allowed to install or replace Warning this equipment.
  • Page 38 The following information will help you to plan the location of the chassis. Plan for access to both the front and rear panels of the Cisco RPS. • Make sure that the room where the Cisco RPS operates has adequate •...
  • Page 39: Setting The Cisco Rps On A Desktop

    Rack-Mounting the Cisco RPS This sections explains how to rack-mount the Cisco RPS in 19-, 23-, 24-inch, or telco equipment racks. Read the following information before rack-mounting your chassis. Cisco Redundant Power System Hardware Installation Guide...
  • Page 40: Planning Your Rack-Mount Installation

    Install the Cisco RPS and the external device to which it will connect in • adjacent shelves in a rack.
  • Page 41: Tools And Equipment Required

    Installing the Cisco RPS Rack-Mounting the Cisco RPS Tools and Equipment Required You need the following tools and equipment to rack-mount the Cisco RPS: Number 2 Phillips screwdriver (not included) • Screws for attaching the Cisco RPS to the rack (not included) •...
  • Page 42: Attaching Brackets

    Installing the Cisco RPS Rack-Mounting the Cisco RPS Figure 2-2 Telco Bracket Attaching Brackets To install the Cisco RPS in a rack, attach the brackets in one of the following ways: With the Cisco RPS front panel forward (see Figure 2-3).
  • Page 43 Note: The second bracket attaches to the other side of the chassis. Figure 2-4 Bracket Installation—Rear Panel Forward DC OUT PUT 2 DC OUT PUT 3 DC OUT PUT 4 Note: The second bracket attaches to the other side of the chassis. Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 44: Mounting The Chassis In A Rack

    DC OUT PUT 4 Note: The second bracket attaches to the other side of the chassis. The brackets can also be installed with the Cisco RPS front panel forward. Mounting the Chassis in a Rack After the brackets are secured to the chassis, use your own screws to attach the...
  • Page 45: Chapter 3 Connection Requirements

    Caution with certain International Electrotechnical Commission (IEC) standards. Do not connect the Cisco RPS to an uninterruptible power supply (UPS) that has not been tested and designed for power-factor-corrected power systems. Do not connect the Cisco RPS to a ferro-resonant transformer. If you do either of these things, you could damage the Cisco RPS.
  • Page 46: Tools And Equipment Required

    • Upgrade kit—Needed for routers that originally came with AC or DC power • supplies (Cisco 2500 and Cisco 2600 series routers; Cisco 3620, Cisco 3640, and Cisco 3725 routers; Cisco 4000 series routers; and the Cisco MC3810 multiservice concentrator)
  • Page 47: Ordering Cables

    Chapter 3 Connection Requirements Ordering Cables Cisco 2500 and Cisco 2600 series routers; Cisco 3620, Cisco 3640, and • Cisco 3725 routers; Cisco 4000 series routers; and the Cisco MC3810 multiservice concentrator support: One-to-one cable for quasi-redundancy – Two-to-one Y-cable for full redundancy –...
  • Page 48 Product number External device CAB-RPSY-2208 Cisco 2500 series routers and Cisco MC3810 multiservice concentrators CAB-RPSY-2218 Cisco 2600 series routers, Cisco 3620, Cisco 3640, and Cisco 3725 routers, and Cisco 4000 series routers Figure 3-2 One-to-One Cable Load unit RPS side...
  • Page 49 Use of cables other than the ones listed can cause damage to the Cisco RPS or external device. 2. This configuration is not recommended due to the 30-second reboot and downtime. Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 50: Upgrade Kit With Power Adapter Plate For Routers And Concentrators

    Catalyst 3500 series XL switches ship with an RPS connector and do not require a power adapter plate. If you did not order your router or concentrator with a Cisco RPS connector installed, you must order a power adapter plate that provides compatibility and must install the plate in place of your existing power supply.
  • Page 51: Chapter 4 Connecting The Cisco Rps

    Before connecting to external devices, read the power warnings below. We recommend that you disconnect all power before beginning. If you want to connect an additional external device to a Cisco RPS that is already Note powered up, you can do so without interrupting power to the Cisco RPS or any other connected external devices.
  • Page 52: Connecting Hubs

    Chapter 4 Connecting the Cisco RPS Connecting Hubs Attach only the Cisco RPS (model PWR600-AC-RPS) to the RPS receptacle. To Warning see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.
  • Page 53 Chapter 4 Connecting the Cisco RPS Connecting Hubs The Cisco RPS can also be used with the older FastHub 100, 200, and 300 series Note hubs. All hubs can use the one-to-one cable configuration for quasi-redundancy. The FastHub 400 series also supports the option of connecting the AC power cord for redundancy with reboot, although this configuration is not recommended.
  • Page 54 10-5 A 1000 W 10-5 A 1000 W On the Cisco RPS rear panel, connect an AC power cable to either or both of the Step 4 power connectors. Use the cable locks on the Cisco RPS to lock the cables in place.
  • Page 55 Connecting the AC Power Cables to the Cisco RPS Cable locks Step 5 Connect the other end of the Cisco RPS AC power cable into an AC power outlet. If you are using the redundant-with-reboot configuration (not recommended), Step 6 power up the switch by connecting the hub AC power cord to an AC power outlet.
  • Page 56: Connecting Switches

    Powering Up the Cisco RPS Power switch The Cisco RPS provides power in 10 to 15 seconds. The Cisco RPS is working properly when all its front-panel LEDs are solid green. If the external device does not power up, refer to Chapter 5, “Troubleshooting the Cisco RPS.”...
  • Page 57 Chapter 4 Connecting the Cisco RPS Connecting Switches Connect one end of the one-to-one cable to the Cisco RPS connector on the switch Step 2 rear panel. (For connector locations, see Figure 4-6 through Figure 4-12.) Figure 4-6 Catalyst 1900 Switch Rear Panel...
  • Page 58 Catalyst 2912M XL and Catalyst 2924M XL Switch Rear Panel RATING 100-120/ 200-240V 2.0A/1.0A 50-60HZ DC INPUTS FOR REMOTE POWER SUPPLY SPECIFI ED IN MANUAL . @24A, +12V @1.0A CONSOL E DC INPUT Cisco RPS AC power connector connector Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 59 Figure 4-11 Catalyst 3512 XL and Catalyst 3524 XL Switch Rear Panel RATING 100-127/20 0-240V~ 1.0A/0.5A 50-60HZ AC power Cisco RPS connector connector Figure 4-12 Catalyst 3548 XL Switch Rear Panel RATING 100-127/20 0-240V~ 1.0A/0.5A 50-60HZ AC power Cisco RPS connector connector Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 60 10-5 A 1000 W 10-5 A 1000 W On the Cisco RPS rear panel, connect an AC power cable to either or both of the Step 4 power connectors. Use the cable locks on the Cisco RPS to lock the cables in place.
  • Page 61 Connecting Switches Figure 4-14 Connecting the AC Power Cables to the Cisco RPS Cable locks Connect the other end of the Cisco RPS AC power cable into an AC power outlet. Step 5 Step 6 If you are using the redundant-with-reboot configuration (not recommended), power up the switch by connecting the switch AC power cord into an AC power outlet.
  • Page 62 Chapter 5, “Troubleshooting the Cisco RPS.” If you are using a Cisco RPS with a revision level lower than Z3 with a Catalyst Note 3508G or a Catalyst 3548 XL switch, the switch RPS LED and the RPS DC LED might display amber (normally indicating Cisco RPS malfunction) even when the Cisco RPS is functioning properly.
  • Page 63: Connecting Routers And The Cisco Mc3810 Concentrator

    Concentrator This section provides illustrations and cabling information for connecting the Cisco RPS to Cisco 2500 series and Cisco 2600 series routers; Cisco 3620, Cisco 3640, and Cisco 3725 routers; Cisco 4000 series routers and Cisco MC3810 multiservice concentrators. All these devices use: One-to-one cable for quasi-redundancy •...
  • Page 64 Chapter 4 Connecting the Cisco RPS Connecting Routers and the Cisco MC3810 Concentrator Figure 4-16 Cisco 2500 Series Router Rear Panel Cisco RPS connector On/off switch Figure 4-17 Cisco 2600 Series Router Rear Panel Cisco 2611 LINK LINK ETHERN ET 0 ACT...
  • Page 65 SEE MANUAL BEFORE INSTALLATION SERIAL ETHERNET 1 ETHERNET 0 ETHERNET 1 ETHERNET 0 INPUT 100-240VA C 50/60HZ 3.0-1.5 AMPS Figure 4-20 Cisco 4000 Series Router Rear Panel On/off Cisco RPS switch connector Cisco Redundant Power System Hardware Installation Guide 4-15...
  • Page 66 Chapter 4 Connecting the Cisco RPS Connecting Routers and the Cisco MC3810 Concentrator Figure 4-21 Cisco MC3810 Multiservice Concentrator Rear Panel ETHE RNE T 0 SER IAL 0 SER IAL 1 CON SOLE Cisco RPS connector On/off switch Connect the other end of the one-to-one or Y-cable to the rear panel connector on...
  • Page 67 10-5 A 1000 W 10-5 A 1000 W On the rear panel of the Cisco RPS, connect an AC power cable to either or both Step 4 of the power connectors. Use the cable locks on the Cisco RPS to lock the cables in place.
  • Page 68 Step 7 position. The Cisco RPS is on and provides power to the external device in 10 to 15 seconds. The Cisco RPS is working properly when all its front-panel LEDs are solid green. If the external device does not power up, see Chapter 5, “Troubleshooting the...
  • Page 69: Troubleshooting The Cisco Rps

    The key to troubleshooting is to isolate the problem to a specific subsystem. Start by reading the LEDs on the front panel of the Cisco RPS and any error messages displayed on the external device console. If you are unable to resolve the problem, refer to the “Getting Technical Support”...
  • Page 70: Reading The Leds

    Reading the LEDs Some external devices also have LEDs that show the operating condition of the Note Cisco RPS. Refer to the installation guide that accompanied the device for detailed information about the LEDs. Table 5-1 lists symptoms indicating a problem, along with possible causes and suggested corrective actions.
  • Page 71 DC output module is to the DC output connectors on the loose, or the internal DC output Cisco RPS rear panel. Check the LEDs to Note The DC LED is module has failed. determine which connector is affected.
  • Page 72 • failed. FAN LED is amber. One of the fans has failed. The The Cisco RPS continues to operate with a remaining fans switch to full single fan failure. To correct the failure, speed to keep the Cisco RPS replace the Cisco RPS. Contact your Cisco cool.
  • Page 73: Displaying Status

    DC status is normal. Board Temperature: Warning: Board overtemperature condition detected. If the Cisco RPS gets too hot, it shuts down to prevent damage to its components. Caution If thermal shutdown occurs because the cooling system failed or the ambient temperature rose above normal operating limits, a thermal warning displays on the router console, and an SNMP trap is sent before shutdown.
  • Page 74: Routers

    Chapter 5 Troubleshooting the Cisco RPS Error Messages on Cisco 2600 Series and Cisco 3620, Cisco 3640, and Cisco 3725 Routers Error Messages on Cisco 2600 Series and Cisco 3620, Cisco 3640, and Cisco 3725 Routers When a Cisco RPS status failure is detected while connected to Cisco 2600 series, Cisco 3620, Cisco 3640, and Cisco 3725 routers, Cisco IOS software receives an interrupt and displays the error messages on the router console.
  • Page 75: Ac Failure

    The value of ciscoEnvMonSupplyState is a warning. How to Correct Error: Check the DC LEDs on the front panel of the Cisco RPS to determine which cable is loose or if the module has failed, and try the corrective actions described in Table 5-1.
  • Page 76 Chapter 5 Troubleshooting the Cisco RPS Error Messages on Cisco 2600 Series and Cisco 3620, Cisco 3640, and Cisco 3725 Routers Console Error Message: When an external device console monitor screen displays the Cisco IOS • software prompt ( routername>...
  • Page 77: Fan Failure

    *** System Environmental Interrupt *** WARNING: REDUNDANT POWER SUPPLY THERMAL BIT IS ASSERTED. Error Description: One of the Cisco RPS fans has failed. The remaining fans switch to full speed to keep the Cisco RPS cool. SNMP Trap Issued Upon Error: ciscoEnvMonRedundantSupplyNotification is generated.
  • Page 78: Temperature Error

    Chapter 5 Troubleshooting the Cisco RPS Error Messages on Cisco 2600 Series and Cisco 3620, Cisco 3640, and Cisco 3725 Routers How to Correct Error: The Cisco RPS continues to operate with a single fan failure, but to correct the failure, replace the Cisco RPS.
  • Page 79 Check the temperature of the room where the Cisco RPS is located, and • correct the temperature setting if it is above 40 Check the front and rear panels of the Cisco RPS to make sure they are clear • of any obstructions.
  • Page 80: Multiple Errors

    The value of ciscoEnvMonSupplyState is a warning. How to Correct Error: Look at the LEDs on the Cisco RPS front panel to determine the types of failures that have occurred. Go to the section in Table 5-1 describing each failure type for instructions on how to correct it.
  • Page 81: Replacing An External Device

    Replacing an External Device If an external device (hub, switch, router, or concentrator) that is receiving power from the Cisco RPS fails, you can replace it without powering down the Cisco RPS or interrupting power to any other external devices. Follow these steps to replace a failed external device that is connected to the Cisco RPS: Do not power down the Cisco RPS.
  • Page 82: Getting Technical Support

    Brief explanation of the steps you have taken to isolate the problem • If the product is under warranty or is covered by a Cisco maintenance contract, contact Cisco’s Technical Assistance Center (TAC) at 800 533-2447, 408 526-7209, tac@cisco.com, or http://www.cisco.com.
  • Page 83: Appendix

    A P P E N D I X Technical Specifications The technical specifications for the Cisco RPS are listed in Table A-1. Table A-1 Specifications Environmental Ranges Operating temperature 32 to 104°F (0 to 40°C) Storage temperature –4 to 149°F (–20 to 65°C)
  • Page 84: Table

    3.44 x 17.5 x 16 in. (8.73 x 44.45 x 40.64 cm) For agency approval and compliance information, refer to the Regulatory Compliance and Safety Information document that accompanied the Cisco RPS. Cisco Redundant Power System Hardware Installation Guide OL-3654-01...
  • Page 85 Catalyst 2900 series XL switches, equipment racks connecting error messages, reading on Cisco 2600 series Catalyst 3500 series XL switches, and Cisco 3620, Cisco 3640, and Cisco connecting 3725 routers Caution symbol, meaning of Cisco Redundant Power System Hardware Installation Guide IN-1 OL-3654-01...
  • Page 86 RPS Note symbol, meaning of front panel, Cisco RPS fully redundant configuration output power per Cisco RPS module output voltage from Cisco RPS HP 10BASE-T Hub-16M, connecting humidity Cisco Redundant Power System Hardware Installation Guide IN-2 OL-3654-01...
  • Page 87 Technical Assistance Center (TAC) xix, 5-14 Cisco 1516M hub telco brackets, product number Cisco 2500 series router 4-14 temperature, operating Cisco 2600 series router 4-14 TEMP LED 1-11 Cisco 3620 router 4-14 Cisco Redundant Power System Hardware Installation Guide IN-3 OL-3654-01...
  • Page 88 Index upgrade kits 3-2, 3-6 voltage input warnings, installation Y-cables Cisco Redundant Power System Hardware Installation Guide IN-4 OL-3654-01...

This manual is also suitable for:

Rps

Table of Contents