Page Table - Sony HVR-Z1J Service Manual

Ver. 1.7 2007. 10
The changed portions from
Ver. 1.6 are shown in blue.
5. 13 Page Table (Mechanism Control Microprocessor
Version 3.0 (MP3) to Version 8.0 (MP8))
Note1: When reading or writing the 13 page data, select page: 0, address:
10, and set data: 01, then select 8 page. The 13 page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to "00".
Note2: Fixed data-1: Initialized data. (Refer to "1. Initializing the 8, C,
13, 18, 1C Page Data".)
Fixed data-2: Modified data. (Refer to "2. Modification of 8, C,
13, 18, 1C Page Data").
Note3: When the mechanism control microprocessor is replaced, check
that the data of the fixed data address shown in the table is the
initial value. If not, change the data to the initial value.
Refer to "1. Initialization of 8, C, 13, 18, 1C page data" for the
version check of the mechanism control microprocessor.
Address
Initial value
00 to 03
04 08
05 00
06 46
07 01
08 02
09 00
0A 00
0B 00
0C to 12
13
14 to 24
25
26 to 89
8A 55
8B 61
8C to B6
B7 0C
B8 60
B9 60 or 78
BA to BD
BE 00 or 01
BF to D5
D6 00 or 3C
D7 00 or 0A
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
Remark
Serial No. input
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data (Note3)
Fixed data-1
Fixed data (Note3)
Fixed data (Note3)
60: Mechanism control microprocessor
Ver 3.0 (MP3) to Ver. 6.0 (MP6)
78: Mechanism control microprocessor
Ver. 7.0 (MP7) or Ver. 8.0 (MP8)
Fixed data-1
Fixed data (Note3)
00: Mechanism control microprocessor
Ver 3.0 (MP3) to Ver. 7.0 (MP7)
01: Mechanism control microprocessor
Ver. 8.0 (MP8)
Fixed data-1
Fixed data (Note3)
00: Mechanism control microprocessor
Ver 3.0 (MP3) to Ver. 7.0 (MP7)
3C: Mechanism control microprocessor
Ver. 8.0 (MP8)
Fixed data (Note3)
00: Mechanism control microprocessor
Ver 3.0 (MP3) to Ver. 6.0 (MP6)
0A:Mechanism control microprocessor
Ver. 7.0 (MP7) or Ver. 8.0 (MP8)
Address
Initial value
D8 00 or 3C
D9 00 or 1E
DA
DB 05 or 1E or 1D
DC 01 or 11 or 15
DD 1E
DE 1E
DF to E8
E9 81
EA to ED
EE 80
EF to FF

6. 18 Page Table

Note1: When reading or writing the 18 page data, select page: 0, address:
10, and set data: 01, then select 8 page. The 18 page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
"00".
Note2: Fixed data-1: Initialized data. (Refer to "1. Initializing the 8, C,
13, 18, 1C Page Data".)
Fixed data-2: Modified data. (Refer to "2. Modification of 8, C,
13, 18, 1C Page Data").
Note3: Mechanism control microprocessor ver. 3.0 (MP3) or ver. 4.0
(MP4).
(Refer to "1. Initialization of 8, C, 13, 18, 1C page data".)
Note4: Mechanism control microprocessor ver. 5.0 (MP5) to ver. 8.0
(MP8).
(Refer to "1. Initialization of 8, C, 13, 18, 1C page data".)
Address
00 to FF Fixed data-1
77 Fixed data-2 (Note3)
78 Fixed data-1 (Note4)
79 to 7A Fixed data-1
7B Fixed data-2 (Note3)
7C Fixed data-1 (Note4)
7D to FF Fixed data-1
6-14
Remark
Fixed data (Note3)
00: Mechanism control microprocessor
Ver 3.0 (MP3) to Ver. 6.0 (MP6)
3C: Mechanism control microprocessor
Ver. 7.0 (MP7) or Ver. 8.0 (MP8)
Fixed data (Note3)
00: Mechanism control microprocessor
Ver 3.0 (MP3) to Ver. 6.0 (MP6)
1E: Mechanism control microprocessor
Ver. 7.0 (MP7) or Ver. 8.0 (MP8)
Fixed data-1
Fixed data (Note3)
05: Mechanism control microprocessor
Ver. 3.0 (MP3) to Ver. 5.0 (MP5)
1E: Mechanism control microprocessor
Ver. 6.0 (MP6)
1D:Mechanism control microprocessor
Ver. 7.0 (MP7) or Ver. 8.0 (MP8)
Fixed data (Note3)
01: Mechanism control microprocessor
Ver. 3.0 (MP3) to Ver. 5.0 (MP5)
11: Mechanism control microprocessor
Ver. 6.0 (MP6)
15: Mechanism control microprocessor
Ver. 7.0 (MP7) or Ver. 8.0 (MP8)
Fixed data (Note3)
Fixed data-1
Fixed data (Note3)
Fixed data-1
Fixed data (Note3)
Fixed data-1
Table. 6-1-8.
Remark
Table. 6-1-9.