Adjusting Items When Replacing Main Parts And Boards - Sony HVR-Z1J Service Manual

1-1. Adjusting items when replacing main parts and boards.

• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note: When replacing the drum assy. or the mechanism deck, reset the data of page: 7, address: A7 to A9 to "00". (Refer to "Record of Use check" of "6-4. SERVICE MODE")
*1: There are the two modes, NTSC(60i) and PAL(50i), in each page of E, F, 14, 19, 1E, and 1F.These pages in NTSC(60i) mode and these pages in PAL(50i) mode are independent completely.
When set up NTSC(60i) mode, set the NTSC(60i)/PAL(50i) switch (DB-018 board S201) to "NTSC(60i)". When set up PAL(50i) mode, set the NTSC(60i)/PAL(50i) switch to "PAL(50i)".
(Refer to "1-2-4. INITIALIZATION OF E, F, 14, 19, 1E, 1F PAGE DATA")
*2: Perform the adjustments in both modes, i.e. NTSC(60i) mode and PAL(50i) mode.
*3: When the SP (LSI) control microprocessor is replaced, check that the fixed data are corresponding to the version of the microprocessor.
(Refer to "1-2-3. Initialization of 9, 1D page data".)
*4: When the mechanism control microprocessor is replaced, check that the fixed data on page 6-11 is corresponding to the version of the microprocessor.
(Refer to "1-2-2. Initialization of 8, C, 13, 18, 1C page data".)
Adjustment Adjustment
Section
Initialization of Initialization of A, B, D, 1A,1B page data
8,9,A,B,C,D,E,F,13, Initialization of 8, C, 13, 18, 1C page data
14,18,19,1A,1B,1C, Initialization of 9, 1D page data
1D,1E,1F page data Initialization of E, F, 14, 19, 1E, 1F page data
Origin oscillation check
HALL adj.
MR adj.
Focus ring adj.
Zoom ring adj.
Flange back adj.
AWB standard data input
Camera *2 MAX GAIN adj.
(Refer to Page 6-23) LV standard data input
Auto white balance adj.
Color reproduction adj.
PSD sensor gain adj.
Angular velocity sensor sensitivity adj.
VCO adj.
Backlight adj.
PSIG level adj.
Color EVF VCOM level adj.
RGB AMP adj.
Contrast adj.
White balance adj.
LCD automatic adj.
Contrast adj.(HD)
LCD V COM adj.
Sample hold phase adj.
Transmissive mode white balance adj.
Reflective mode white balance adj.
Mechanism Tape path adj.
System control Serial No. input
CAP FG duty adj.
Servo, RF Switching position adj.
Error rate check
S VIDEO OUT Y level adj.
Video *2
S VIDEO OUT chroma level adj.
(Refer to Page 6-115)
COMPONENT OUTPUT level adj.
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
Block replacement
*1
z
z
z
z
z
z
z
z
z
z
z
z z
z z
z z z
z
z z z
z z z
Table. 6-1-1(1).
6-2
Ver. 1.7 2007. 10
The changed portions from
Ver. 1.6 are shown in blue.
Replaced parts
Parts replacement
z
z
z z
z z
z z
z z
z z
z
z
z
z
z
z
z
z
z
z
z
z
*4
*3
z
z
z
z
z
z z
z
z
z
z
z z
z
z
z
z
z
z
z