Self-Diagnosis Code Table - Sony HVR-Z1J Service Manual

SELF-DIAGNOSIS CODE TABLE

Self-diagnosis Code
Block Detailed
Function Code
C 0 4 0
C 2 1 0
C 2 2 0
C 3 1 1
C 3 1 1
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 3
C 3 1 4
C 3 1 4
C 3 2 1
C 3 2 1
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 3
C 3 2 4
C 3 2 4
E 2 0 0
E 6 1 0
E 6 1 1
E 6 1 1
E 6 2 0
E 6 2 0
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
Symptom/State
0 Non-standard battery is used.
0 Condensation.
0 Video head is dirty.
0 LOAD direction. Loading does not
complete within specified time
1 UNLOAD direction. Loading does not
complete within specified time
0 T reel side tape slacking when unloading.
1 Winding S reel fault when counting the
rest of tape.
2 T reel fault.
3 S reel fault.
4 T reel fault.
0 FG fault when starting capstan.
0 FG fault when starting drum.
2 FG fault during normal drum operations.
LOAD direction loading motor time-
0
out.
UNLOAD direction loading motor
1
time-out.
T reel side tape slacking when
0
unloading.
Winding S reel fault when counting the
1
rest of tape.
2 T reel fault.
3 S reel fault.
4 T reel fault.
0
FG fault when starting capstan.
0 FG fault when starting drum
FG fault during normal drum
2
operations
0 Data on A page or D page are rewriten.
Difficult to adjust focus
0
(Cannot initialize focus.)
Zoom operations fault
0
(Cannot initialize zoom lens.)
The abnormalities in initialization of the
focus lens and the abnormalities in
1
initialization of the zoom lens occurred
simultaneously.
Steadyshot function does not work well.
0 (With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
1 (With yaw angular velocity sensor output
stopped.)
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Make data A page and D page correct value.
Inspect the lens block focus MR sensor (Pin qd, qf of CN1501 of
VC-367 board) when focusing is performed when the focus ring is
rotated in the focus manual mode, and the focus motor drive circuit
(IC1702 of VC-367 board) when the focusing is not performed.
Inspect the lens block zoom MR sensor (Pin ra, rs of CN1501 of
VC-367 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive circuit (IC1702 of VC-367
board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and check
whether it is inserted imperfectly. If there is no problem in the
flexible board, inspect the focus/zoom motor drive circuit (IC1702
of VC-367 board).
Inspect pitch angular velocity sensor (SE401 of SE-150 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE402 of SE-150 board)
peripheral circuits.
6-137
Correction