Color Reproduction Check Nd 1 Sd Cine Γ; Color Reproduction Check Nd 2 Sd Cine Γ - Sony HVR-Z1J Service Manual

23-2. Color Reproduction Check ND 1 SD CINE γ
Subject
Measurement Point
Measuring Instrument
Specified Value
Note1: The data of page: 0, address: 10 must be "00".
Note2: Check that the data of page: 6, address: 02 is "00". If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Note3: When using the vectorscope, disconnect the cable from the
COMPONENT connector.
Switch setting:
1) REC FORMAT (IN/OUT REC menu) .............................. DV
(Page: 6, Address: 9B, Bit2=1)
2) ND FILTER .............................................................................. 1
(Page: 6, Address: 9B, Bit4=1, Bit5=0)
3) STEADY SHOT (CAMERA SET menu) ........................ OFF
4) FOCUS .................................................................. MANUAL
5) ZOOM ........................................................................ LEVER
Adjusting method:
Order Page Address Data
1
2 0 01
3 6 8A
4 6 9B
5 6 01
6 6 9D
7 6 9E
8 6 12
9 6 12
10
11
Note4: For the bit values, refer to "6-4. SERVICE MODE", "4-3. 3. Bit
value discrimination".
Note5: The Y signal terminal (Pin 1) of the COMPONENT connector
must be terminated at 75 Ω.
70 IRE = 490 mV, 68 IRE = 476 mV
Processing after Completing Adjustments:
Order Page Address Data
1 6 01
2 6 8A
3 6 9D
4 0 01
5
HVR-Z1J/Z1U/Z1N/Z1E/Z1P/Z1C
Color bar chart
(HD color bar standard picture frame)
NTSC or PAL vectorscope: Video
terminal of AUDIO/VIDEO jack (Note3)
Oscilloscope: COMPONENT
connector
All color luminance points should
settle within each color reproduction
frame (SD CINE γ). (Fig. 6-1-24.)
Procedure
Set ND FILTRE switch to "1".
01 Set the data.
04 Set the data.
Check that bit3 is "1". (Note4)
4D Set the data, and press PAUSE
button.
Change the data and set the Y
signal level (A) to 70 IRE
(NTSC) or 68 IRE (PAL).
(Note5) (Fig. 6-1-23.)
22 Set the data.
80 Set the data.
00 Set the data.
Check that the Y signal level (A)
is 70 IRE (NTSC) or 68 IRE
(PAL).
Check that each center of all
color luminance points is set in
each color reproduction frame.
Procedure
00 Set the data, and press PAUSE
button.
00 Set the data.
00 Set the data.
00 Set the data.
Set ND FILTRE switch to
"OFF".
23-3. Color Reproduction Check ND 2 SD CINE γ
Subject
Measurement Point
Measuring Instrument
Specified Value
Note1: The data of page: 0, address: 10 must be "00".
Note2: Check that the data of page: 6, address: 02 is "00". If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Note3: When using the vectorscope, disconnect the cable from the
COMPONENT connector.
Switch setting:
1) REC FORMAT (IN/OUT REC menu) .............................. DV
(Page: 6, Address: 9B, Bit2=1)
2) ND FILTER ........................................................................... 2
(Page: 6, Address: 9B, Bit4=0, Bit5=1)
3) STEADY SHOT (CAMERA SET menu) ........................ OFF
4) FOCUS .................................................................. MANUAL
5) ZOOM ........................................................................ LEVER
Adjusting method:
Order Page Address Data
1
2 0 01
3 6 8A
4 6 9B
5 6 01
6 6 9D
7 6 9E
8 6 12
9 6 12
10
11
Note4: For the bit values, refer to "6-4. SERVICE MODE", "4-3. 3. Bit
value discrimination".
Note5: The Y signal terminal (Pin 1) of the COMPONENT connector
must be terminated at 75 Ω.
70 IRE = 490 mV, 68 IRE = 476 mV
Processing after Completing Adjustments:
Order Page Address Data
1 6 01
2 6 8A
3 6 9D
4 0 01
5
6
6-52
Color bar chart
(HD color bar standard picture frame)
NTSC or PAL vectorscope: Video
terminal of AUDIO/VIDEO jack (Note3)
Oscilloscope: COMPONENT
connector
All color luminance points should
settle within each color reproduction
frame (SD CINE γ). (Fig. 6-1-24.)
Procedure
Set ND FILTRE switch to "2".
01 Set the data.
04 Set the data.
Check that bit3 is "1". (Note4)
4D Set the data, and press PAUSE
button.
Change the data and set the Y
signal level (A) to 70 IRE
(NTSC) or 68 IRE (PAL).
(Note5) (Fig. 6-1-23.)
22 Set the data.
80 Set the data.
00 Set the data.
Check that the Y signal level (A)
is 70 IRE (NTSC) or 68 IRE
(PAL).
Check that each center of all
color luminance points is set in
each color reproduction frame.
Procedure
00 Set the data, and press PAUSE
button.
00 Set the data.
00 Set the data.
00 Set the data.
Set ND FILTRE switch to
"OFF".
Set REC FORMAT to
"HDV1080i".