Table of Contents
Advertisement
1 5 . 4 . 7
U A R T x M o d e m C o n t r o l R e g i s t e r
T h i s r e g i s t e r c o n t r o l s t h e i n t e r f a c e w i t h t h e m o d e m o r d a t a s e t ( o r a p e r i p h e r a l d e v i c e
e m u l a t i n g a m o d e m ) . T h e c o n t e n t s o f t h e M o d e m C o n t r o l r e g i s t e r a r e d e s c r i b e d b e l o w :
T a b l e 5 7 1 . U A R T x M o d e m C o n t r o l R e g i s t e r - ( U x M C R ) ( S h e e t 1 o f 2 )
s
3 1
t e
P
b u
r v
I O
r i
t t
A
e s
u t
I
P C
i b
n a
t r
A t
U n i t #
0
1
B i t
31:6
5
4
®
I n t e l
8 1 3 4 1 a n d 8 1 3 4 2 I / O P r o c e s s o r s
D e v e l o p e r ' s M a n u a l
8 9 8
2 8
2 4
r v
r v
r v
r v
r v
r v
r v
r v
r v
r v
n a
n a
n a
n a
n a
n a
n a
n a
n a
n a
®
I n t e l X S c a l e
C o r e i n t e r n a l b u s a d d r e s s
+ 2 3 1 0 H ( D L A B = x )
+ 2 3 5 0 H ( D L A B = x )
D e f a u l t
000 0000h
Reserved
Autoflow Control Enable (AFE): When set, autoflow control is enabled. Only auto-
CTS is enabled when RTS is cleared in MCR while AFE is set. Both auto-CTS and
auto-RTS are enabled when AFE and RTS in MCR are set. Auto-RTS is not enabled
when AFE is not set regardless of the state of RTS.
0
Autoflow automates the flow of data between the UART and the remote device. See
2
Section 15.3.4, "Autoflow Control" on page 885
0 = Auto-RTS and Auto-CTS are disabled
1 = Auto-CTS is enabled. IF RTS in MCR is also set, both auto-CTS and auto-RTS
is enabled
Loop back test mode (LOOP): This bit provides a local Loopback feature for
diagnostic testing of the UART. In the Diagnostic mode, data that is transmitted is
immediately received. This feature allows the processor to verify the UART Transmit
and Receive data paths. The Transmit, Receive and Modem Control Interrupts are
operational. The modem-control input CTS# is activated by MCR bit 1 instead of the
modem-control input. A Break signal can also be transferred from the transmitter
section to the receiver section in Loop-Back mode.
When LOOP is set (1), the following occurs:
• The TXD (transmitter output) pin is set to a logic-1 state.
• The RXD (receiver input) pin is disconnected.
• The output of the Transmitter Shift register is "looped back" into the Receiver-
Shift register input.
0
2
• The modem-control input CTS# is disconnected from the pins and the modem-
control output pin RTS# is forced to the inactive state.
The RTS bit of the Modem Control register is connected to bits of the Modem Status
register bits. Flow control can be tested; when autoflow is enabled the RTS bit of the
Modem Control Register has no effect on the CTS# input as RTS# is asserted by the
autoflow logic.:
• RTS = 1 forces CTS to a 1
Note:
Note: Coming out of the Loop-Back Test mode may result in unpredictable
activation of the delta bit (bit 0) in the Modem Status register (MSR). It is
recommended that MSR is read once to clear the delta bits in the MSR.
0 = Normal UART operation
1 = Test mode UART operation
2 0
1 6
1 2
r v
r v
r v
r v
r v
r v
r v
r v
r v
r v
n a
n a
n a
n a
n a
n a
n a
n a
n a
n a
A t t r i b u t e L e g e n d :
R V = R e s e r v e d
P R = P r e s e r v e d
R S = R e a d / S e t
D e s c r i p t i o n
®
I n t e l
8 1 3 4 1 a n d 8 1 3 4 2 — U A R T s
8
4
r v
r v
r v
r v
r v
r w
r w
r w
p r
n a
n a
n a
n a
n a
n a
n a
n a
n a
R W = R e a d / W r i t e
R C = R e a d C l e a r
R O = R e a d O n l y
N A = N o t A c c e s s i b l e
for more details.
D e c e m b e r 2 0 0 7
O r d e r N u m b e r : 3 1 5 0 3 7 - 0 0 2 U S
0
r w
r v
n a
n a
Advertisement
Chapters
Table of Contents
