Enter User Codes - Gemini GEM-P9600 Programming Instructions Manual

WI777D 08/00
ENTER USER CODE
U01 123___ -F3 -__
User# User Code
!
Press the ( ) button to set the cursor to the User Code. Use the number buttons
A
enter a code of up to 6 digits. Enter up to 6 digits (4 digits is recommended) in the first six boxes from left to right for
each user code. Valid entries are: 0-9. Note: Press the
blank (•) any trailing boxes. If an "Ambush Code" (Address 0495) is entered, do not program the first two digits of ANY
User Code as the same digits entered for the "Ambush Code".
!
If the programmed code is less than 6 digits, press the
the tables below for the available User Option and User Level data entries. Enter the user options data in the left digit.
Enter the level data (with arming options, if any, added) in the right digit. Note: For entries greater than 9, press the
buttons through the
G1
!
For Keypad Access Control, press the
below, use the number buttons to enter the data for Keypad 1–4 in the right digit; and the data for Keypad 5–8 data in
the left digit. (Press the
Example: Enter a code of "123456" as
"123456" (from left to right).
USER OPTIONS
DATA BLOCKED USER BYPASS
ENTRIES VIEW PROGRAM
blank (•) DISABLED
1 Y
2 Y
3 Y Y
4 Y
5 Y Y
6 Y Y
7 Y Y Y
8
9 Y
0 Y
B Y Y
C Y
D Y Y
E Y Y
F Y Y Y
Note: "Y" indicates option is enabled.
L
NAPCO Security Systems
Enter User Codes (Press the (
Enter up to 96 User Codes with User Options, Authority Level and Access
Control Options (if necessary) for each code. Refer to the tables below and
on the next page for available data entries for User Options, Authority Level
Option Access
and Access Control Options. Note: All 96 Users must be assigned to areas
/Level Control
in "Enable User Code by Area" (Address 2500-2595) in Direct Address
Programming. By default, only User 1 is enabled in Area 1 and Area 2.
User 2 - 8 are enabled in Area 1 and user 9 - 16 are enabled in Area 2.
buttons for B through F, respectively.
G5
button once again to program applicable keypads. Refer to the tables
A
buttons for blank.)
0
USER CODE
(UP TO 6 DIGITS)
DATA AUTHORITY
ENTRIES LEVEL
OVERVIEW
blank (•) NONE
1 LEVEL 1
2 LEVEL 2
3 LEVEL 3
4 NONE
5 LEVEL 1
6 LEVEL 2
7 LEVEL 3
8 NONE
Y 9 LEVEL 1
Y 0 LEVEL 2
Y B LEVEL 3
Y
Y
Y
Y
Y
A
button for a zero. No blank spaces in between; leave
0
button to set the cursor to the OPTION/LEVEL. Refer to
A
USER OPTIONS
USER USER ACCESS CONTROL
OPTION LEVEL KEYPADS
CODE ACCESS CONTROL KEYPADS
TYPE
DATA K.P. 5 K.P. 6 K.P. 7 K.P. 8
ENTRIES
ARM/DISARM
ARM/DISARM
blank (•)
ARM/DISARM
1 Y
ARM/DISARM
2 Y
ARM ONLY
3 Y Y
ARM ONLY
4
ARM ONLY
5 Y
ARM ONLY
6 Y
SERVICE
7 Y Y
SERVICE
8
SERVICE
9 Y
SERVICE
0 Y
B Y Y
C
D Y
E Y
F Y Y
Note: "Y" indicates option is enabled.
X
GEM-P9600 Programming Instructions
) button to set cursor.)
through
1 9
ACCESS CONTROL KEYPADS
DATA K.P. 1 K.P. 2 K.P. 3 K.P. 4
ENTRIES
NONE blank (•)
1 Y
2
3 Y
Y 4
Y 5 Y
Y 6
Y 7 Y
Y 8
Y 9 Y
Y 0
Y B Y
Y Y C
Y Y D Y
Y Y E
Y Y F Y
Note: "Y" indicates option is enabled.
!
Page 9
to
NONE
Y
Y
Y
Y
Y Y
Y Y
Y
Y
Y Y
Y Y
Y Y
Y Y
Y Y Y
Y Y Y