Central Station Receiver 1 Tel. Number; Central Station Receiver 1 Account Number - Gemini GEM-P9600 Programming Instructions Manual

WI777D 08/00
EXIT/ENTRY ZONES
ENTER ZONE # 00
(Direct Entry)
NOTE: Exit/Entry Zones will have an entry delay of 30 seconds and an exit delay of 60 seconds. Chime will automatically
be programmed for all E/E zones. If you are programming a 2 Area system, enter all of the zones required for Areas 1 & 2.
INTERIOR ZONES
ENTER ZONE # 00
(Direct Entry)
NOTE: All Interior zones will also be automatically programmed as "Exit/Entry Follower" zones. If you are programming a
2 Area system, enter all the zones required for Areas 1 & 2.
# A R E A 1 K E Y P A D S
E N T E R # K P S 0 1
(Direct Entry)
# A R E A 2 K E Y P A D S
E N T E R # K P S 0 0
(Direct Entry)
CENTRAL PHONE #
_ _ _ _ _ _ _ _ _ _ _ _ _
(Direct Entry)
Delay = "D"; Dial-Tone Detection = "E". Pressing the
NEXT ( ) to proceed. NOTE: Central Station Receiver 2 and 3 Telephone Numbers can only be entered in Direct
E
Address Programming. See CS Receiver Options.
Easy Programming of Auto download ID #'s and PC Preset Callback Numbers (GEM-RP1CAe2 only)
For unattended PC Preset downloading, it is now possible to set the Auto download ID #'s and PC Preset Callback from
the Keypad Easy Program Mode.
•
At the field for CENTRAL PHONE #, program an "F" followed by the Auto Download ID # (2 digits) and then the
Callback Telco # (up to 13 digits).
•
Press [ON/OFF] to save.
•
Exit Program Mode ([RESET] [RESET]).
•
Enter Master Code
•
Press [FUNCTION]
•
Go to Function "ACTIVATE DOWNLOAD Y/N" and press YES (INTERIOR).
•
The panel will automatically call the PC Preset computer and download the program on the specified Auto
Download line # of PC Preset.
CENTRAL PHONE #
F 0 7 1 5 1 6 8 4 2 9 4 0 0
•
Go to Central Phone # input screen and press: [*] [5] [0] [7] [1] [5] [1] [6] [8] [4] [2] [9] [4] [0] [0] [ON/OFF]
L
NAPCO Security Systems
Exit/Entry Zones (Appears for New Panel Only)
Directly enter the zone numbers which are to be used as Exit/Entry zones.
Valid entries are from 01 to 96. Directly enter each zone number, including
leading zeros. Use number buttons
button for a zero. Press
0
zone(s). Press NEXT (
E
Interior Zones (Appears for New Panel Only)
Directly enter the zone numbers which are to be used as Interior Zones. Valid
entries are from 01 to 96. Directly enter each zone number, including leading
zeros. Use number buttons
J
button for a zero. Press
Press NEXT ( ) button to proceed.
E
Number of Keypads in Area 1
Directly enter the total number of Keypads to be installed in Area 1. Valid
entries are from 01 to 15. Directly enter the number of keypads, including
leading zeros. Use number buttons
button for a zero. Press
0
Number of Keypads in Area 2
Directly enter the total number of Keypads to be installed in Area 2. Valid
entries are from 01 to 15.
Central Station Receiver 1 Telephone Number
Using number buttons, enter telephone number of up to 16 digits including
prefix letters, if necessary, for receiver 1. Use number buttons
for digits 1–9; press the
9
through
1 G 5
button will produce a blank space (•). Press
0
Example: Program an Auto download ID # of 07 and a PC Preset Callback #
of 1-516-842-9400
X
through
1 9
J
to save and then repeat for any additional
) button to proceed.
through . NOTE: Press the
1 9
to save and then repeat for any additional zone(s).
through
1 9
J
to save. Press NEXT (
button for a zero and
G 0
for letters B–F, respectively. NOTE: Pre-Dial
GEM-P9600 Programming Instructions
!
Page 7
. NOTE: Press the
0
. NOTE: Press the
) to proceed.
E
through
1
G
J
to save. Press