Gemini GEM-P9600 Programming Instructions Manual page 23

WI777D 08/00
07
BYPASS FIRE/TBL
INTERIOR
FIRE/TBL
INTERIOR BYPASS
(Direct Entry)
08
INTERIOR BYPASS FIRE/TBL
BYPASS FIRE/TBL
INTERIOR
(Direct Entry)
09
BYPASS FIRE/TBL
INTERIOR
FIRE/TBL
INTERIOR BYPASS
(Direct Entry)
10
BYPASS FIRE/TBL
INTERIOR
INTERIOR BYPASS FIRE/TBL
(Direct Entry)
11
BYPASS FIRE/TBL
INTERIOR
BYPASS FIRE/TBL
INTERIOR
(Direct Entry)
L
NAPCO Security Systems
Exit/Entry Zones (Appears for New Panel Only)
Directly enter the zone numbers which are to be used as Exit/Entry zones.
Valid entries are from 01 to 96. Directly enter each zone number, including
SYS TBL CHIME
leading zeros. Use number buttons
button for a zero. Press
0
zone(s). Press NEXT (
SYS TBL CHIME
NOTE: Exit/Entry Zones will have an entry delay of 30 seconds and an exit
delay of 60 seconds. Chime will automatically be programmed for all E/E
zones. If you are programming a 2 Area system, enter all of the zones
required for Areas 1 & 2.
Interior Zones (Appears for New Panel Only)
Directly enter the zone numbers which are to be used as Interior Zones. Valid
entries are from 01 to 96. Directly enter each zone number, including leading
zeros. Use number buttons
SYS TBL CHIME
button for a zero. Press
Press NEXT (
NOTE: All Interior zones will also be automatically programmed as "Exit/
SYS TBL CHIME
Entry Follower" zones. If you are programming a 2 Area system, enter all the
zones required for Areas 1 & 2.
Number of Keypads in Area 1
Directly enter the total number of Keypads to be installed in Area 1. Valid
entries are from 01 to 15. Directly enter the number of keypads, including
SYS TBL CHIME
leading zeros. Use number buttons
button for a zero. Press
0
SYS TBL CHIME
Number of Keypads in Area 2
Directly enter the total number of Keypads to be installed in Area 2. Valid
entries are from 01 to 15. Directly enter the number of keypads, including
SYS TBL CHIME
leading zeros. Use number buttons
button for a zero. Press
0
proceed.
SYS TBL CHIME
Central Station Receiver 1 Telephone Number
Using number buttons, enter telephone number of up to 16 digits including
prefix letters, if necessary, for receiver 1. Use number buttons
SYS TBL CHIME
for digits 1–9; press the
9
through
1
Delay = "D"; Dial-Tone Detection = "E". Pressing the
SYS TBL CHIME
produce a blank space (•). Press
proceed. NOTE: Central Station Receiver 2 and 3 Telephone Numbers can
only be entered in Direct Address Programming. See CS Receiver Options.
1
J
to save and then repeat for any additional
) button to proceed.
E
through
1
J
to save and then repeat for any additional zone(s).
) button to proceed.
E
1
J
to save . Press NEXT (
1
J
to save . Press NEXT (
G 0
for letters B–F, respectively. NOTE: Pre-Dial
G 5
J
to save. Press NEXT (
X
GEM-P9600 Programming Instructions
Page 23
through . NOTE: Press the
9
. NOTE: Press the
9
through . NOTE: Press the
9
) to proceed.
E
through . NOTE: Press the
9
) button to
E
through
1
button for a zero and
button will
0
) button to
E
!
0
G