Gem-Rp3Dgtl Keypad - Gemini GEM-P9600 Programming Instructions Manual

!
Page 22
B. GEM-RP3DGTL Keypad
Enter the Master Security Code (printed on microprocessor can) for a new panel or enter your custom
GEMINI
SYSTEM ARMED
Dealer Program Code if programmed. Press
1 7
ENT A1
01/01/97 12:00AM
INT ERIOR BY PA SS F IRE/T B L SY S T BL CHIM E
NEXT/YES
A 1 2 3 E
D
displayed. NOTE: If you pass Function "17", you can scroll back by pressing the
PRIOR/NO
B 4 5 6 F
AREA
C 7 8 9 0 G
YES (
E
COMPUTERIZED SECURITY SYSTEM
R
keypad. The questions will be in the form of a 2 digit number flashing in the digital display. Press the
button to
A
01
BYPASS FIRE/TBL
INTERIOR
FIRE/TBL
INTERIOR BYPASS
(Direct Entry)
02
BYPASS FIRE/TBL
INTERIOR
FIRE/TBL
INTERIOR BYPASS
(Direct Entry)
04
INTERIOR BYPASS FIRE/TBL
FIRE/TBL
INTERIOR BYPASS
(Direct Entry)
05
INTERIOR BYPASS FIRE/TBL
BYPASS FIRE/TBL
INTERIOR
(Direct Entry)
06
BYPASS FIRE/TBL
INTERIOR
BYPASS FIRE/TBL
INTERIOR
(Yes or No)
X
GEM-P9600 Programming Instructions
) to enter the Dealer Program Mode. The GEM-RP3DGTL is a dual 7-segment digital
scroll through each segment.
Flashing
Total Number of Zones in Area 1 & Area 2 (Appears for New Panel Only)
Directly enter the total number of zones to be programmed for Area 1 and
Area 2, respectively. Valid entries are from 01 to 96. Directly enter the total
SYS TBL CHIME
number of zones, including leading zeros. Use number buttons
through
9
based on groups of 4 zones each (after the first 8 zones), and will
automatically round up to the next group of 4. For example, if you enter 18,
SYS TBL CHIME
it will automatically convert this to 20 zones. Press
( ) button to proceed.
E
Note: The GEM-P9600 is limited to a combined maximum of 96 zones and
15 keypads. All 96 zones and 15 keypads may be programmed in the EZ
SYS TBL CHIME
Program Mode. For more options, see Zone and Keypad Options in Direct
Address Programming.
SYS TBL CHIME
Fire Zones (Appears for New Panel Only)
Enter the zone number of any Fire Zones (both 2-wire, 4-wire or wireless).
Valid entries are from 01 to 96. Directly enter each zone number, including
SYS TBL CHIME
leading zeros, and press
zone(s). Press NEXT (
NOTE: If you are programming a 2 Area system, enter the zone number of
zones required for Areas 1 & 2. All fire zones are common to areas 1 and 2.
SYS TBL CHIME
The Direct Address Program Mode can then be used to customize them as
needed. See Zone Options.
2-Wire Fire Zones (Appears for New Panel Only)
Enter the zone number of any Fire Zones (from previous question) which
are to be used with 2-wire smoke detectors. The only valid entries are 01
SYS TBL CHIME
through 08. Directly enter each zone number, including leading zeros. Press
J
to save, and then repeat for any additional zone(s). NOTE: Only zones
which have been designated as Fire Zones can be programmed as 2 Wire
Fire zones. Press NEXT (
SYS TBL CHIME
to "2-WF" position for 2-wire fire zones 7 and 8 (refer to Installation
Instructions).
Local System or C.S. Reporting System (Appears for New Panel Only)
Press YES (
for no zones to report (LOCAL SYSTEM).
SYS TBL CHIME
SYS TBL CHIME
followed by NO (
A,
. NOTE: Press the
0
J
to save, and then repeat for any additional
) button to proceed.
E
) button to proceed. NOTE: JP7 must be set
E
) button for all zones to report; press NO (
E
WI777D 08/00
) repeatedly until "17" is
F
button. Press
B
button for a zero. The system is
J
to save. Press NEXT
F
L
NAPCO Security Systems
1
) button