Table of Contents
Advertisement
USER MANUAL
3.0 - OPERATING INSTRUCTIONS
3.1 - COMPLETE SYSTEM ARMING
Press the lock button on the vehicle remote control or button
738W);
system arming is confirmed by a siren chirp and a flash of the turn indicators (if optical/acoustic
signals are enabled).
The system has a 30 sec. arming delay during which the LED is ON steady.
3.2 - SYSTEM ARMING WITH SENSORS EXCLUSION
To arm the system without arming interior protection press button "3" on the Gemini remote control.
System arming is confirmed by a quick low-pitched chirp and a flash of the turn indicators (if signals
are enabled).
Sensors can be excluded via the vehicle original remote control on the following vehicles:
›
• FIAT DUCATO '11
›
• FORD TRANSIT '14
• RENAULT MASTER '10
›
To exclude interior protection via the vehicle original remote control, proceed as follows:
• Lock the vehicle via the vehicle original remote control.
• Wait at least 5 sec.,
but before the end of the arming delay
• Exclusion is confirmed by 1 low-pitched chirp.
NB:
THIS CONFIRMATION TONE CANNOT BE EXCLUDED.
Exclusion of sensors is bound to each single arming cycle. They will be reset upon next
3.3 - PASSIVE ARMING
If programmed for passive arming, the system will automatically arm approximately 60 sec. after
ignition is switched OFF and the last door is opened and closed.
Arming is confirmed by a siren chirp and a flash of the turn indicators (if signals are enabled).
If programmed for passive arming, interior protection is excluded.
Opening a door during the 60-second passive-arming countdown will cause the
procedure to interrupt; it will resume once the door is closed.
3.4 - ARMING DELAY
There is a 30 sec. delay from the time the system is armed to allow you to leave the vehicle without
triggering an alarm: it will be signaled by the LED turned ON steady.
3.5 - SYSTEM ARMED
After the arming delay the system is fully armed and ready to detect any alarm event. The LED will start
flashing to confirm the armed status.
PAGE 04 - USER MANUAL
"1" on the Gemini remote control (P/N
, and press the lock button again.
arming.
3.6 - ALARM, NEUTRAL TIME BETWEEN ALARMS AND ALARM CYCLES
Alarm events are signaled by optical/acoustic signals
interval before another alarm can be triggered.
Each alarm event can generate up to 10 cycles for each input and for each arming cycle. One alarm cycle
lasts for 30 sec.
3.7 - SYSTEM DISARMING
Press the unlock button on the vehicle original remote control or button
control (P/N 738W); system disarming is confirmed by 2 siren chirps and 2
indicators (if signals are enabled).
If an alarm event has occurred while you were away from your vehicle, it will be signaled, when you
disarm the sytem, by 5 siren chirps and 5 flashes of the turn indicators.
Alarm causes and relative LED signals are listed in the next paragraph.
3.8 - ALARM MEMORY
The LED memory allows to identify the last alarm event signaled by 5 siren chirps and 5 turn indicator
flashes when the system is disarmed.
Turn ignition key "ON"and count the number of flashes. The status LED will flash according to the last
alarm detected prior to disarming (see table below).
The flash sequence is repeated 3 times; to interrupt turn ignition key "OFF".
The table below lists the various alarm causes and relative number of LED flashes.
LED FLASHES
LED OFF (2 seconds)
LED ON (1 second)
. Once the alarm ceases, there is a 5 sec. time-
"2" on the Gemini remote
flashes of the turn
ALARM
ALARM CAUSES
CYCLES
Ignition attempt (+15/54)
10
Door tamper
10
Bonnet tamper
1
0
Boot tamper
10
Volumetric or external sensor
1
0
Wireless magnetic contacts or
10
opening detectors
Wireless infrared sensors (PIR)
10
Wire tampering
10
USER MANUAL - PAGE 05
Advertisement
Table of Contents
