Key Fob Transmitters; Enter Zone Descriptions; Enter Date - Gemini GEM-P9600 Programming Instructions Manual

!
Page 12
KF A XMIT#+ CS OP
0 1 - 0 0 0 0 0 0 0 : 0 0 0
DATA AUX 1/AUX 2 OPTIONS
ENTRY
0 None
1 Relay Group 1 Toggle
2 Relay Group 2 Toggle
3 Relay Group 3 Toggle
4 Relay Group 4 Toggle
5 Relay Group 5 Toggle
6 Relay Group 6 Toggle
7 Relay Group 7 Toggle
8 Relay Group 8 Toggle
9 Panic
A Auxiliary
B Instant
C Aux. Output Toggle
D Access on Aux. Output
Key Fob Zone Assignment (refer to display as shown on the previous page: press the (
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 =
point 3; A2 = point 4. Up to 96 key fobs (using 1 button) or 48 key fobs (using 2 buttons) or 28 key fobs (using all 4
buttons) or any combination up to a maximum of 96 controlled zones can be assigned, providing multiple wireless panic
buttons on a system, each reporting to the Central Station or a pager and/or annunciating on a keypad the key fob zone
number with description/location. To assign a key fob to a zone: program the keyfob as you would a transmitter, entering
the keyfob's ID code, check sum and point number at the appropriate zone. The "Quick Method" is not allowed. The zone
may be hardwired to a sensor as well as assigned to a key fob (either one will activate the zone alarm output). NOTE: If
assigning a key fob to a zone, the "ON/OFF" buttons on the key fob will no longer arm/disarm the system. The key fob is
converted to a "panic only" device.
01-______________
________________
(Direct Entry)
to the next description, place the cursor under the Zone Number (e.g. "01") and change the Zone Number using the
and buttons. Program a new description as above. NOTE: Zone Descriptions can only be entered through
3 6
the GEM-/RP1CAe2 Keypad or by using the Napco Quickloader Software. Press NEXT (
E N T E R D A T E
( 0 1/ 0 1/ 9 9 )
(Direct Entry)
X
GEM-P9600 Programming Instructions
Key Fob Transmitters (Press the (
Keyfobs can be programmed as "Arm/Disarm" devices.(refer to WI752).
For each Key Fob Transmitter, enter:
!
the Key Fob Transmitter number (01–16).
!
area number to which transmitter is assigned (1-8); enter 0 to disable
keyfob.
! the 6-digit RF ID # printed on the transmitter (enter all numbers and/or letters, including
leading "0"s, if any).
! 1-digit checksum number printed on the transmitter (enter all numbers and/or letters,
including leading "0"s, if any).
! Aux-1 Option (see key fob aux 1 & aux 2 options).
! Aux-2 Option (see key fob aux 1 & aux 2 options).
Note: If the Key Fob is converted for Two Button "Emergency Use" (by cutting an internal
jumper), both top or bottom buttons must be depressed to activate an alarm. In this case,
Aux-1 and Aux-2 cannot be programmed. Press
proceed.
Enter Zone and Interior Descriptions
Press the
and
6
description of up to two lines. Press
Enter Date (Press the (
Enter the current date in the format MM/DD/YY, where MM = the month
(01–12); DD=the day (01–31); and YY=the year. Press
NEXT (
E
A
J
to save. Press NEXT (
and buttons to place the cursor; press the
1 2
buttons to select the character. For each zone, enter a
J
) button to set cursor.)
A
) button to proceed.
WI777D 08/00
) button to set cursor.)
NOTE: Key fobs 1-16 report openings and
closings as Users 81-96.
E
) button to go backwards.)
F
to save each description. To proceed
) button to proceed.
E
J
to save. Press
L
NAPCO Security Systems
) button to
3