Gem-Rp1Cae2 Keypad; Number Of Zones & Keypads Per Area; Local Or Central Station Reporting System - Gemini GEM-P9600 Programming Instructions Manual

!
Page 6
A. GEM-RP1CAe2 Keypad
To create your customized default program using a GEM-RP1CAe2 keypad, enter the following
GEMINI
SYSTEM ARMED AI #ZN=08 #KP=1 # OF ZONES IN AREA 1
A2 #ZN=00 #KP=0
01/01/97 12:00AM
ENTER # ZONES X X parameters. In each of the following steps, press the
NEXT/YES
A 1 2 3 E
D
PRIOR/NO
B 4 5 6 F
button to go forwards, the PRIOR (
AR EA
C 7 8 9 0 G
COMPUTERIZED SECURITY SYSTEM
R
button twice to exit at any time.
#OF ZNS IN AREA1
ENTER # ZONES 08
(Direct Entry)
#OF ZNS IN AREA2
ENTER # ZONES 00
(Direct Entry)
Note: The GEM-P9600 is limited to a combined maximum of 96 zones and 15 keypads. All 96 zones and 15 keypads may
be programmed in the EZ Program Mode. For more options, see Zone and Keypad Options in Direct Address
Programming.
F I R E Z O N E S
ENTER ZONE # 00
(Direct Entry)
NOTE: If you are programming a 2 Area system, enter the zone number of zones required for Areas 1 & 2. All fire zones
are common to areas 1 and 2. The Direct Address Program Mode can then be used to customize them as needed. See
Zone Options.
2 - W I R E F I R E Z N S
E N T E R Z O N E # 0 0
(Direct Entry)
which have been designated as Fire Zones can be programmed as 2 Wire Fire zones. Press NEXT (
proceed. NOTE: JP7 must be set to "2-WF" position for 2-wire fire zones 7 and 8 (refer to Installation Instructions).
REPORT ALL ZONES
TO CENTRAL? Y/N
(Press YES or NO)
X
GEM-P9600 Programming Instructions
) button to go backwards, the
F
Total Number of Zones in Area 1 & Area 2 (Appears for New Panel Only)
Directly enter the total number of zones to be programmed for Area 1 and
Area 2, respectively. Valid entries are from 01 to 96. Directly enter the total
number of zones, including leading zeros. Use number buttons
through . NOTE: Press the
9
based on groups of 4 zones each (after the first 8 zones), and will
automatically round up to the next group of 4. For example, if you enter 18,
it will automatically convert this to 20 zones. Press
( ) button to proceed.
E
Fire Zones (Appears for New Panel Only)
Enter the zone number of any Fire Zones (both 2-wire, 4-wire or wireless).
Valid entries are from 01 to 96. Directly enter each zone number, including
leading zeros, and press
zone(s). Press NEXT (
E
2-Wire Fire Zones (Appears for New Panel Only)
Enter the zone number of any Fire Zones (from previous question) which
are to be used with 2-wire smoke detectors. The only valid entries are 01
through 08. Directly enter each zone number, including leading zeros. Press
J
to save, and then repeat for any additional zone(s). NOTE: Only zones
Local System or C.S. Reporting System (Appears for New Panel Only)
Press YES ( ) button for all zones to report; press NO (
E
for no zones to report (LOCAL SYSTEM).
button to set cursor, the NEXT (
A
J
button to save and the
button for a zero. The system is
0
J
J
to save, and then repeat for any additional
) button to proceed.
L
NAPCO Security Systems
WI777D 08/00
)
E
C
1
to save. Press NEXT
) button to
E
) button
F