Advertisement
ALARM OPERATION WITH BASIC CONFIGURATION
Arming
Pressing the (dotted) button #1 on the remote control or inserting the electronic
key into the receptacle will activate the alarm.
This action is indicated by one long flashing of the turn signals, two short
acoustic signals and the permanent turning on of the LED
Engine passive arming
The passive engine immobiliser is actived from the system 40" after the turn-off
of the vehicle.
Lifting up the seat or opening the trunk (if the supplementary button is installed)
during the 40" of the immobiliser pre-arming, the time count will be cancelled
and restarts when the seat or the trunk are closed.
The engine immobiliser is also actived after 40" by remote disarming.
In both cases engine passive arming
is indicated by two acoustic signals and
two turn signals flashes.
When the engine block is activated the LED flash quickly.
It's sufficient to turn the vehicle ignition key in "ON" position and press one
button of the remote to disarm the passive engine immobiliser.
Trunk open
lifted-up seat signalling
During alarm activation, should the seat or the trunk be opened, the alarm will
signal the failure by means of a low-tone beep (BOOP) after the alarm arming
signalling.
In any case the alarm will be activated and, at the end of the "neutral time", an
alarm condition will be generated.
Neutral time
When the activation signals are finished, the alarm goes in standby or neutral-
time condition, which is signalled with a steady-light LED.
This time duration is about 20 seconds.
The engine immobilization function and the connectors for optional modules
are already active.
Excluding the siren
D
uring the first 4 seconds in neutral time, the alarm siren can be deactivated,
by simply pressing (smooth) button #2 on the remote control.
Siren deactivation will be signalled by a short flashing of the turn signals.
NOTE
When the siren is deactivated, the alarm signals will change correspondingly.
Indeed only visual signals will be active, i.e. with flashing of the turn signals, but
the engine immobilization function will still work.
The siren sound exclusion is bound to the single arming cycle.
PAG.6
During the first 4" of neutral time, it is possible to exclude the alarm built-in
sensor (lifting); to do this, you must just put the electronic key into the specific
receptacle, after the alarm system has been activated.
The exclusion is bound to a single arming cycle and will be indicated by a short
flashing of the status led.
.
At the end of the neutral time, after about 20 seconds, the alarm goes in the
armed condition and signals this with a blinking led.
From now on, the alarm is ready to signal possible attempts to force the
vehicle.
If, during the alert state, should occur any theft attempt against the vehicle, the
alarm will signal this by activating the high-volume siren, lighting up the red led
with a steady light and causing the direction indicators to flash repeatedly for
about 30 seconds.
The alarm may be activated by different causes, which also depend on the
activated functions described below
!
Cut-off of the power supply cables
!
Turn on the ignition key (
!
Shifting attempt
!
Opening of the seat or the trunk.
!
Panic alarm, by pushing (smooth) button #2 on the remote control
When the alarm conditions are over, the system will revert to the alert state.
During the alarm condition it is still possible to deactivate the siren by pushing
button #2 (smooth) on the remote control (without disarming the alarm).
Alarm conditions caused by shock, shifting/hitting, seat or trunk opening, will
be signalled by the activation of the siren for 8 times.
From the sixth alarm condition on, the siren will cease to be active.
This deactivation of the siren is performed because of these simple reasons:
!
Observance of the regulations in force in the subject of acoustic emissions
caused by vehicle alarms.
!
Power saving, to maximize the vehicle battery.
!
It is no use keeping the alarm on if, after 8 acoustic signals, nobody is
coming to check the vehicle.
!
Noise pollution reduction, to prevent penalties as the regulations in force.
Once the alarm cycle is over, the device will ignore any other alarm cause for
eight seconds, while keeping the led steadily on.
After this interval, the LED will start blinking again.
Excluding the built-in sensor
Armed condition
Alarm
:
.
positive under key
).
.
Limiting the acoustic signal
Neutral time between two alarm signals
PAG.7
Advertisement
