Smooth Fitness VT-3.4 Owner's Manual page 7

"A
I
SSEMBLY NSTRUCTIONS"
To allow for
easier assembly
do not fully
tighten the
sliding rail
assembly bolts
until step3 is
completed
b. Fully tighten the two Washers (8x16x2.0t)(80), two Lock Washers (M8)(79) and two Bolts (M8xp1.25x90mm)(101)
that attach to the Front Stabilizer (2) to the Main Frame (1).
S –
TEP 2 Sliding Rail Assembly
NOTE: For shipping purpose, the 1pcs Washer (8x16x2.0t)(80), 1pcs Lock Washer (M8)(79) and 1pcs
Bolt (M8xp1.25x20mm)(103) are pre-installed in the Main Frame (1) as pictured on the left.
a. Remove the 1pcs Washer (8x16x2.0t)(80), 1pcs Lock Washer (M8)(79) and 1pcs Bolt
(M8xp1.25x20mm)(103) from the Main Frame (1).
b. Attach the Left Sliding Rail (4) to the Main Frame (1) and secure it with the 1pcs Washer
(8x16x2.0t)(80), 1pcs Lock Washer (M8)(79) and 1pcs Bolt (M8xp1.25x20mm)(103). To allow for
easier assembly of the rear stabilizer to the main frame, do not fully tighten washers and bolts
(79, 80 and 103 until step 3 has been completed).
c. Next, attach the Securing Cap (30) and secure it with the 1pcs Bolt (M6xp1.0x25mm)(93).
d. Repeat the above process for the right side.
S –
TEP 3 Rail Sleeve & Rear Stabilizer Assembly
a. Attach the Rail Sleeve (31) to the Rear Stabilizer (3).
NOTE: For shipping purposes, the 2pcs Washers (8x16x2.0t)(80), 2pcs Lock Washers (M8)(79)
and 2pcs Bolts (M8xp1.25x20mm)(103) are preinstalled in the back of the Rear Stabilizer (3) as pictured above.
b. Remove the 2pcs Washers (8x16x2.0t)(80), 2pcs Lock Washers (M8)(79) and 2pcs Bolts (M8xp1.25x20mm)(103)
from the back of the Rear Stabilizer (3).
c. Next, align the Rear Stabilizer (3) with the Main Frame (1) and then attach the Left and Right Sliding Rail (4,5) to
the Rear Stabilizer (3).
d. Follow the picture at the top of the page for the assembly process. Now secure the sliding rail to the rear stabilizer by
using the 2pcs Washers (8x16x2.0t)(80), 2pcs Lock Washers (M8)(79), 2pcs Bolts
(M8xp1.25x20mm)(103), 2pcs Carriage Bolt (M8xp1.25x90mm)(109) and 2pcs Nylon Nuts
(M8xp1.25)(112).
e. Go back to Step 2 to fully tighten the 2pcs Washers (8x16x2.0t)(80), 2pcs Lock Washers (M8)(79) and
2pcs Bolts (M8xp1.25x20mm)(103) on two upper sides of the sliding rail.
f. Attach the Leveler (23) and Nut (M8xp1.25)(114) to the middle of the Main Frame's base (1). Adjust the
Leveler (23) until it meets the floor so that is levels the equipment. Then tighten the Nut (114) securely
against the Main Frame (1). NOTE: The purpose of adjusting the Leveler (23) is to level the item and give
more support to the base of the Main Frame. Adjust the Leveler (23) until the item sets on the floor without rocking.
S
Assembly
a. Attach the Front Stabilizer (2) to
NOTE: Insert all the screws and
bolts from each step before fully
tightening them.
To make the assembly of the
Front Stabilizer (2) to the Maine
Frame (1) easier, it is suggested
to place a small block of packing
foam under the mainframe, then
insert the two Washers
(8x16x2.0t)(80), two Lock
Washers (M8)(79) and two Bolts
(M8xp1.25x90mm)(101) through
the Front Stabilizer (2) and then
through the Maine Frame (1).
7
–
TEP 1 Front Stabilizer
the Main Frame (1).