NetComm NTC-40WV User Manual page 67

List of valid commands (which can be used in conjunction with the execute command):
"pdpcycle", "pdpdown" and "pdpup" commands can have a profile number suffix 'x' added. Without the suffix specified, the
command operates against the current active profile or last active profile.
# COMMAND NAME
1 reboot
2 pdpcycle or pdpcyclex
3 pdpdown or pdpdownx
4 pdpup or pdpupx
The following table lists valid variables where "x" is a profile number (1-6). If no profile is specified, variables are read or written to for
the current active profile. If a profile is specified, variable are read or written to for the specified profile number ('x').
# RDB VARIABLE NAME
link.profile.x.enable
link.profile.x.apn
link.profile.x.user
0 link.profile.x.pass
link.profile.x.auth_type
link.profile.x.iplocal
link.profile.x.status
1 link.profile.x.apn
link.profile.x.user
2
link.profile.x.pass
3
4 link.profile.x.auth_type
link.profile.x.iplocal
5
6 wwan.0.radio.information.signal_strength
wwan.0.imei
7
statistics.usage_current
8
statistics.usage_current
9
10 /proc/uptime
wwan.0.system_network_status.current_ba
11
nd
www.netcommwireless.com
4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299
Immediately perform a soft reboot
Disconnect (if connected) and reconnect the 3G connection. If a profile number is selected in the
command, try to disconnect/reconnect the specified profile in case the profile is active. If no profile
number is selected, try to disconnect/reconnect the current active profile. Reports an error if no profile
number is selected and there is no currently activated profile.
Disconnect the PDP. If a profile number is selected in the command, try to disconnect the specified
profile in case the profile is active. If no profile number is selected, try to disconnect the current active
profile. Reports an error if no profile number is selected and there is no currently activated profile.
Reconnect the PDP. If a profile number is selected in the command, try to connect with the specified
profile. If no profile number is selected, try to connect to the last active profile. The gateway will check
the currently activated profile and disconnect this profile before executing the command. Reports an
error if no profile number is selected and there is no stored last active profile number.
Table 30 - List of Valid SMS Diagnostic Commands
SMS VARIABLE READ/
NAME WRITE
profile
or RW
profilex
apn or apnx RW
username or usernamex RW
password or password RW
authtype or authtypex RW
wanip or wanipx R
rssi R
imei R
usage R
wanuptime R
deviceuptime R
band R
Table 31 - List of SMS Diagnostics Variables
DESCRIPTION
DESCRIPTION
Read:
(profile no,apn,user,pass,auth,iplocal,status)
1,Telstra.internet,username,password,
chap,202.44.185.111,up
Profile
Write:
(apn, user, pass,auth)
telstra.internet,username,password
APN telstra. Internet
3G username Guest, could also return "null"
3G password Guest, could also return "null"
3G Authentication
"pap" or"chap"
type
WAN IP address 202.44.185.111
3G signal strength 65 dBm
IMEI number 359102128941027512
"Rx 500 bytes, Tx 1024 bytes, Total 1524
3G data usage of
bytes" or "Rx 0 byte, Tx 0 byte, Total 0 byte"
current session
when wwan down
Up time of current 3G 1 days 02:30:12 or 0 days 00:00:00 when
session wwan down
Device up time 1 days 02:30:12
Current 3G frequency WCDMA 850
NTC-40WV HSPA+ M2M WiFi Router with Voice
EXAMPLE
67