NetComm NTC-40WV User Manual
  1. Manuals
  2. Brands
  3. NetComm Manuals
  4. Wireless Router
  5. NTC-40WV
  6. User manual

NetComm NTC-40WV User Manual

Hspa+ m2m wifi router with voice
Hide thumbs Also See for NTC-40WV:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
HSPA+ M2M WiFi Router
with Voice

USER GUIDE

4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NTC-40WV and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for NetComm NTC-40WV

Summary of Contents for NetComm NTC-40WV

  • Page 1: User Guide

    HSPA+ M2M WiFi Router with Voice USER GUIDE 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 2 Copyright© 2012 NetComm Wireless Limited. All rights reserved. The information contained herein is proprietary to NetComm Wireless. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of NetComm Wireless.

  • Page 3: Table Of Contents

    RJ-45 Connector ......................................80 Captive Power Terminal Block ..................................80 Additional Product Information ..............................81 Using the NTC-40WV to make and receive telephone calls ........................... 81 Handset requirements ..................................81 Maximum REN Loading ..................................81 How to place a call ....................................81 How to receive a call ....................................

  • Page 4: Overview

    Overview Introduction This document provides you all the information you need to set up, configure and use the NTC-40WV router. Target Users This document is intended for system integrators or experienced hardware installers who understand telecommunications terminology and concepts. Prerequisites Before continuing with the installation of your NTC-40WV Router, please confirm that you comply with the minimum system requirements below.

  • Page 5: Product Introduction

    2 x WiFi Antennas (SMA connector)   1 x RJ-45 Ethernet Cable If any of these items are missing or damaged, please contact NetComm Wireless Support immediately by visiting the NetComm Wireless Support website at: http://support.netcommwireless.com www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice...

  • Page 6: Product Features

    Product Features The NTC-40WV is a robust 3G (HSPA+) router designed to provide real-time M2M data connectivity even in harsh environments, and allows you to build wide area networks utilising the superior speeds supported by 3G UMTS networks. The router integrates a powerful mobile broadband module and delivers download speeds of up to 21Mbps which is then transmitted via Ethernet to a WiFi router inside the property.

  • Page 7: Physical Dimensions And Indicators

    Physical Dimensions and Indicators LED Indicators The NTC-40WV uses 5 LEDs to display the current system and connection status. Figure 1 - NTC-40WV LED Indicators DISPLAY DESCRIPTION Power (red) Solid ON The red Power LED indicates correct power is applied to the DC power input jack.

  • Page 8: Physical Dimensions

    Physical Dimensions Below is a list of the physical dimensions of the NTC-40WV, as well as the physical dimensions of the antennas and the included mounting bracket which can be used to attach the NTC-40 to a pole or to provide a wall / ceiling mount.
  • Page 9 Length 35mm (when folded up at 90 degrees as per diagram) Depth 13mm Height 115mm Table 5 - 3G Antenna Dimensions www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 10: Interfaces

    Interfaces The following interfaces are available on the NTC-40WV: Figure 5 - Bottom Mounted interfaces ITEM INTERFACE FUNCTION Diversity Receive 3G Antenna Connect one of the 3G antennas here SIM Card Reader Tray Eject button Push in with a paper clip to eject the SIM card reader tray.

  • Page 11: Ntc-40Wv Default Settings

    NTC-40WV Default Settings The following tables list the default settings for the NTC-40WV. LAN (MANAGEMENT) Static IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1 Table 8 - LAN Management Default Settings WIRELESS (WIFI) NetComm XXXX where XXXX are a SSID: set of 4 random digits.

  • Page 12: Restore Factory Default Settings

    Use a pen to depress the Reset button on the device for 10 seconds. The router will restore the factory default settings and reboot. Once you have reset your NTC-40WV Router to its default settings you will be able to access the device’s configuration web interface using http://192.168.1.1...

  • Page 13: Implementation And Deployment Scenario

    Implementation and Deployment Scenario The robust and intelligent NTC-40WV HSPA+ M2M WiFi Router is designed to provide real-time M2M data connectivity in a single device, even in harsh environments. Utilising a NetComm M2M router allows customers to significantly reduce the cost of the deployment and operation of new products and services in remote locations.

  • Page 14: Installation And Configuration Of The Ntc-40Wv

    NTC-40WV Connecting via an Ethernet cable Connect the Ethernet cable provided to the port marked “Ethernet” on the side of the NTC-40WV. Connect the other end of the yellow Ethernet cable to your computer. Wait approximately 30 seconds for the connection to establish.

  • Page 15: Web Based User Interface

    Web based User Interface To log in to the management console and view the status and make changes to your NTC-40WV, please follow the steps below: Open your web browser (e.g. Internet Explorer/Firefox/Safari) and navigate to http://192.168.1.1 Enter the username and password and click the “Submit” button. For the first time set up please log on with username “root”...

  • Page 16: Status

    Status The status page provides system related information and is displayed when you login to the NTC-40WV management console. By default, the status page will show System Information, Ethernet Port Status, WWAN Status, IPSec Status and the 3G service connection details.
  • Page 17 The Remote LAN IP address of the IPSec tunnel. Status The current status of the IPSec tunnel. Table 16: Status Page - IPSec Details www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 18 Table 17: Status Page - Call Forwarding Settings NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 19: Advanced Status

    The Advanced Status page provides advanced system related information and is displayed when you click on the Advanced Status button at the bottom of the NTC-40WV status page. The Advanced Status page shows information regarding the on-board 3G module as well as statistics of the current 3G connection.
  • Page 20 The Mobile Subscriber ISDN Number uniquely identifying a subscription in a GSM or a MSISDN UMTS mobile network. Table 18: Status - Advanced Status Item Details NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 21: Internet Settings

    Click on the “Internet Settings” menu followed by “Mobile Broadband” and then the “Connection” menu item on the right. Figure 16 - Connection Settings www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 22 “Save”. This is because the router saves the manually configured APN profile in flash memory and will always try to connect to that APN first regardless of whether “Automatically configure my mobile broadband” is enabled. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com...
  • Page 23 This is particularly useful if you have more than one PPPoE router or modem on a single Ethernet network. Click “Save” to save your settings and enable PPPoE. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 24 “Apply”. The “Automatic” option is sufficient for most users. It will choose the most appropriate operator based on the inserted SIM card. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 25 Alternatively you can also disable SIM PIN protection by selecting to “Disable PIN” from the “PIN Protection” drop down menu. Click Save. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 26 When this feature is disabled and the SIM is PIN locked, the PIN must be manually entered via the router‘s configuration interface. This is clearly not desirable where the router is unattended. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com...

  • Page 27: Lan

    There should be no need to disable this feature in most cases, however, if you need to do so simply select “Disable” and click the Save button. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 28 Enter a name for the computer or device. Enter the computer or device’s MAC address. Enter the IP address to assign to the device. Click the “Save” button. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 29 To relay the DHCP function from a remote DHCP server: Set the “DHCP Relay” option to Enable. Enter the IP Address of the DHCP Server you wish to relay to. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 30: Routing

    The new static route will be displayed at the bottom of the Static Routes section. Deleting Static Routes Click the “Delete Entry” text (in blue). NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 31 Figure 29 - RIP Settings  Click Enable for the “RIP Enable” option.  Select the RIP version.  Click the “Save RIP” button. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 32 IP address (VRRP IP) or on a command prompt type: arp –d <ip address> (i.e. arp –d 192.168.1.1) to clear the arp cache.(old MAC address). NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 33 “Incoming Port Range”. To delete a port forwarding rule, click on the corresponding “Delete Entry” link from the list of IP Mappings. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 34 Enter the IP Address of the device to be the DMZ host into the “DMZ IP Address” field. Click the “Save” button. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 35: Vpn

    Each VPN connection has different configuration requirements. For more information on the VPN functionality available, please refer to the VPN document available from the NetComm Wireless Website. The following pages detail the configuration options available for the different VPN connection types.
  • Page 36 Figure 34 - VPN Connection Settings – IPSec The table on the following page describes each of the fields of the IPSec VPN Connection Settings page. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 37 Each type of Key mode requires different configuration options. For more information, please refer to the VPN Document available from the NetComm Website. Table 20 - IPSec Configuration Items www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 38 From the menu at the top of the screen, click “Internet Settings” then “VPN” and “OpenVPN”. A list of configured OpenVPN VPN connections is displayed. Figure 35 - OpenVPN VPN List Click the “Add” button to begin configuring an OpenVPN VPN connection. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 39 Each type of Key mode requires different configuration options. For more information, please refer to the VPN Document available from the NetComm Wireless Website. Table 21 - OpenVPN Configuration Items www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 40 Figure 37 - PPTP Client List Click the “Add” button to begin configuring an PPTP-Client VPN connection. Figure 38 - VPN Connection Settings - PPTP NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 41 The delay before attempting to reconnect to the VPN service. Reconnect Retries The number of times to attempt to reconnect to the VPN service. Table 22 - PPTP Configuration Items www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 42 Figure 39 - GRE VPN List Click the “Add” button to begin configuring a GRE VPN connection. Figure 40 - GRE VPN Settings page NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 43 The delay before attempting to reconnect to the VPN service. Reconnect Retries The number of times to attempt to reconnect to the VPN service. Table 23: VPN - GRE Settings www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 44 Any responses from your 3G Service Provider will be displayed in the “Response from Network” box in the middle of the page. Please contact your 3G Service provider for a list of available USSD commands for your 3G service. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com...

  • Page 45: Wireless Settings

    Figure 42 - Wireless Configuration - Basic Settings OPTION DEFINITION WiFi is turned on by default. Changing this option to OFF will turn OFF the wireless functionality on the NTC-40WV and you will not Radio On/Off be able to connect wirelessly.
  • Page 46 Figure 44 - Advanced View – WiFi Security Settings - WPA-PSK/WPA2-PSK Note: Your NTC-40WV uses WPA2-PSK by default. Check your Wireless Security Card or the device label on the bottom of the NTC-40WV for your default SSID and Security key to begin connecting your wireless devices.
  • Page 47 Point 1 is connected to a mobile broadband network and Access Point 2 and its clients will connect to the internet through Access Point 1. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 48 Configure the LAN IP Address of Access Point 1. In this example, it is set to the default address of 192.168.1.1: Figure 47 - WDS - Access Point 1 LAN IP Setup NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com...
  • Page 49 Click Wireless Settings and then Basic. Enter the required details as listed in the table below: Figure 49 – WDS - Access Point 1 Repeater Mode Setup www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 50 Access Point 2 will act as a repeater for and provide internet access to its clients through Access Point 1 and therefore does not require a Mobile Broadband connection to be established. Figure 50 – WDS - Aceess Point 2 Status NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 51 Figure 51 - WDS - Access Point 2 LAN IP Setup Set the DHCP Server on Access Point 2 to Disable: Figure 52 - WDS - Access Point 2 DHCP Settings www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 52 Wireless Distribution System (WDS) section. When you have entered the required information, click Save: Figure 53 - WDS – Access Point 2 Repeater Mode Setup The Wireless Distribution System setup is now complete. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 53: Advanced

    Table 26 - Wireless Settings - Advanced Configuration Items Click the “Save” button to save any advanced settings changes. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 54: Mac Filtering

    MAC address is listed in the MAC filter list will be denied network access. All other wireless client devices will be allowed network access. Figure 55 - Wireless LAN - MAC Filtering NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 55: Station List

    Station List The Station List page shows the number of devices currently connected to your NTC-40WV via Wireless. The MAC address, Host Name and IP address of these devices are displayed. Figure 56 - Wireless Station List www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice...

  • Page 56: Services

    Click the “Save” button to save the new settings. The NTP (Network Time Protocol) settings page allows the NTC-40WV to synchronise its internal clock with a global Internet Time server. This setting provides an accurate timekeeping function for features such as System Log entries and Firewall settings where the current system time is displayed and recorded.

  • Page 57: System Monitor

    The default value is 0 which disables the “Forced Reset Every” field. The maximum value is 65535 minutes. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 58: Snmp

    Table 27 - SNMP Configuration Options You can also trigger an SNMP Heartbeat manually by clicking the “Send Heartbeat Now” button. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 59: Sms

    The UDP port on which to connect to the remote destination on. Enable Remote Diagnostics Enable diagnostics to be performed by a specially crafted SMS message. Table 28 -SMS Setup Settings www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 60 It is highly recommended to enable security when utilising this feature. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 61 After entering the required recipient numbers, type your SMS message in the “Message Body” field and then click the “Send” button. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 62 Simply select the sender or recipient number and click the “Add White List” button. Figure 63 - SMS Inbox Figure 64 - SMS Outbox NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 63 This can be useful to determine if a command was received and executed by the router. This is disabled by default. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 64 White List as well as setting a password for each phone number entered. This prevents unauthorised or accidental execution of SMS commands. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 65 A password (if required), only needs to be specified once per SMS, but can be prefixed to each command if desired. “PASSWORD get Variable1”; “get VARIABLE2” www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 66 “PASSWORD execute reboot; getVariable1”; “get VARABLE2” “PASSWORD execute reboot; PASSWORD get Variable1”; “get VARABLE2” Commands are case insensitive, however variable names and values are case sensitive. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 67 Device up time 1 days 02:30:12 wwan.0.system_network_status.current_ba band Current 3G frequency WCDMA 850 Table 31 - List of SMS Diagnostics Variables www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 68 Send multiple set command Required Password1234 set APN=”3netaccecss”; set password=NetComm Table 32 - SMS Diagnostics - Example Commands NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 69: Auto Dial

    Enter the number to be automatically dialled when the attached handset is picked up. Table 33 - Auto Dial Configuration Items After entering the required auto dial telephone number, click the “Save” button. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 70: System

    You can also download the current System Log to your computer for off-line viewing. To do this, click the “Download Log File” link at the bottom of the page. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 71: Load / Save

    To restore the router’s configuration to the factory defaults Click Restore to restore the factory default configuration. The router will then restart with the factory default configuration loaded. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 72 Upload The Upload page enables you to upload firmware files or user created application packages to the NTC-40WV. Figure 69 - Upload Page The firmware of the router can be updated locally via LAN connection and also via remote access. Both upgrade types follow a similar process.
  • Page 73 Figure 74 - Recovery Console - Firmware Update The router will confirm you want to restart and then start up with the new system software loaded. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 74 “Package Details” link. Alternatively, if you want to remove a package, click the blue “Uninstall” link. Note: For more information on creating software packages for the NTC-40WV, please refer to the SDK document available from the NetComm website.

  • Page 75: Administration

    Note: To perform functions like Firmware upgrade, device configuration backup and to restore and reset the router to factory defaults, you need to login as the root user. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 76: System Configuration

    Note: If the Voice Call Function option is changed, you must click Save and reboot the router for the changes to take effect. NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 77 Verify Password Re-enter the TR-069 connection request password here and press the Save button. Table 37 - System - TR-069 Details www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 78: Logoff

    The reboot item will reboot the router. This can be useful if you have made configuration changes you want to implement or want to reboot the router. Figure 80 - Reboot Router NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 79: Technical Data

    Technical Data The following table lists the hardware specifications of the NTC-40WV. MODEL NETCOMM NTC-40WV Modem Module/Chipset Sierra MC8704 / Qualcomm MDM8200A Wireless LAN IEEE 802.11b/g/n, up to 16 concurrent users RAM: 64MB DRAM Memory Storage: 256MB Flash Operating System Embedded Linux 2.6...

  • Page 80: Rj-45 Connector

    The following table displays the pin outs for the Locking Power Block on the DC adapter. Figure 82 - Locking Power Terminal Block SIGNAL DESCRIPTION Voltage+ Voltage- Table 40 - Locking Power Block Pin Outs NTC-40WV HSPA+ M2M WiFi Router with Voice www.netcommwireless.com 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 81: Additional Product Information

    Handset requirements The NTC-40WV allows you to make telephone calls over the 3G network using a standard analogue telephone via the built in RJ-11 Phone port. Please refer to the documentation provided by the manufacturer of your analogue telephone for assistance with the operation of your telephone handset.

  • Page 82: Call Feature Codes

    Call feature codes Quick Reference Table The NTC-40WV supports a number of call feature codes for supplementary services. FEATURE ACTIVATION DEACTIVATION STATUS #31# *31# Caller ID *#31# (to unblock caller ID for (to block caller ID for outgoing outgoing calls)
  • Page 83 Call the 2nd phone number. After the 2nd phone picks up the call, place both calls into one conference call by performing another hook-flash and then pressing button 3. To terminate the conference call hang up the phone connected to the router. www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...
  • Page 84 What do I do if I have no dial tone? Please follow the procedure listed below: Check to make sure the phone is plugged into your NTC-40WV on the RJ-11 port (between the power socket and the LAN port). Check to make sure you are using the correct cable (Cat-3 UTP Telephone Cable with RJ-11 plugs).

  • Page 85: List Of Mobile Broadband Service Provider Apns

    Telstra Clear www.telstraclear.net.nz Telecom NZ XT wap.telecom.co.nz 2 Degrees internet Table 42 - List of Mobile Broadband Service Provider APNs www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice 4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299...

  • Page 86: Appendix A: Tables

    Table 35 - Administration Configuration Items ......................75 Table 36 - System Configuration Items ........................76 Table 37 - Technical Specifications for the NTC-40WV ....................79 Table 38 - RJ-45 Connector Pin Outs .......................... 80 Table 39 - Locking Power Block Pin Outs ........................80 Table 40 - Additional Product Information - Call Feature Codes Quick Reference ............

  • Page 87: Legal And Regulatory

    NetComm Wireless’ (or its licensors’) intellectual property rights to you. You are permitted to use this Manual for the sole purpose of using the NetComm Wireless product to which it relates. Otherwise no part of this Manual may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic, mechanical, recording or otherwise, without the prior written permission of NetComm Wireless.

  • Page 88: Product Warranty

    Consumer Protection Laws which cannot be excluded, NetComm Wireless’ liability for any breach of that guarantee, condition or warranty is limited to: (i) in the case of a supply of goods, NetComm Wireless doing any one or more of the following: replacing the goods or supplying equivalent goods;...
  • Page 89 Contact Address: NetComm Wireless Limited 18-20 Orion Road, Lane Cove NSW 2066 Sydney, Australia ABN: 85 002 490 486 Website: www.netcommwireless.com Phone: +61(0)2 9424 2070 Fax: +61(0)2 9424 2010 Email: sales@netcommwireless.com techsupport@netcommwireless.com www.netcommwireless.com NTC-40WV HSPA+ M2M WiFi Router with Voice...

This manual is also suitable for:

Hspa+ m2m wifi router

Table of Contents