Mitsubishi Electric MELSEC Q Series User Manual page 179

If Start and End fields in Auto refresh are left blank, auto refresh is not performed. (Start and End fields in Auto refresh in the
Receive tab can be left blank.)
The example for setting blank to the auto refresh setting .of the CPU No.2 in <Flow of sending data from CPU No.3 to other
CPUs> explained in the previous page 3) is shown below.
In the auto refresh setting of CPU No.2 in Figure 4.36, if the Start (W40) and End (W5F) fields of the Auto refresh are left
blank, auto refresh is not performed to W40 to W5F in CPU No.2.
<Parameter setting>
(g) Receive setting from CPU No.3
(1) Auto refresh setting of CPU No.1
Figure 4.36 Auto refresh setting related to sending and receiving CPU No.3 data (Leaving the second row of PLC No.2 blank)
<Flow of sending data from CPU No.3 to other CPUs>
For flow of sending data from CPU No. 3, refer to 3) Flow of sending data from CPU No.3 to other CPUs on
the previous page.
PLC No.1
Multiple CPU high speed transmission area
PLC No.1
User free area User free area
Auto refresh area
PLC No.2
User free area User free area
Auto refresh area
PLC No.3
User free area User free area
Auto refresh area
Device Device
B0 B0
to CPU No.1 send data CPU No.1 send data
B1F
B20 B20
to
CPU No.2 receive area CPU No.2 receive area
B3F
B40 B40
to CPU No.3 receive area CPU No.3 receive area
B5F
W0 W0
to CPU No.1 send data CPU No.1 send data
W1F
W20 W20
to
CPU No.2 receive area CPU No.2 receive area
W3F
W40 W40
to CPU No.3 receive area CPU No.3 receive area
W5F
1) Writing by END processing of CPU No.3 1) Writing by END processing of CPU No.3
2) Sending data from CPU No.3 to CPU No.1 and CPU No.2 2) Sending data from CPU No.3 to CPU No.1 and CPU No.2
3) Reading by END processing of CPU No.1 3) Reading by END processing of CPU No.1
4) Reading by END processing of CPU No.2 4) Reading by END processing of CPU No.2
Figure 4.37 Flow of send data in CPU No.3 to other CPUs when setting blank to No.2 field of PLC No.2
4 - 33
(h) Receive setting of CPU No.3
(2) Auto refresh setting of CPU No.2
Multiple CPU high speed transmission area
PLC No.1
Auto refresh area
PLC No.2
Auto refresh area
PLC No.3 PLC No.3
2)
Auto refresh area
M0 M0
to
CPU No.1 receive area CPU No.1 receive area
M31
M32 M32
to
CPU No.2 send data CPU No.2 send data
M63
3)
M64 M64
to CPU No.3 receive area CPU No.3 receive area
M95
W0 W0
to
CPU No.1 receive area CPU No.1 receive area
W1F
W20 W20
to
CPU No.2 send data CPU No.2 send data
W3F
3)
W40 W40
to CPU No.3 receive area CPU No.3 receive area
W5F
PLC No.2
User free area User free area
User free area User free area
User free area User free area
2)
Device Device
4)
Does not perform refresh.
(i) Send setting from CPU No.3
(3) Auto refresh setting of CPU No.3
PLC No.3
Multiple CPU high speed transmission area
PLC No.1
User free area User free area
Auto refresh area
PLC No.2
User free area User free area
Auto refresh area
PLC No.3 PLC No.3
User free area User free area
Auto refresh area
1)
Device Device
B0 B0
to
CPU No.1 receive area CPU No.1 receive area
B1F
B20 B20
to
CPU No.2 receive area CPU No.2 receive area
B3F
B40 B40
to CPU No.3 send data CPU No.3 send data
B5F
D0 D0
CPU No.1 receive area CPU No.1 receive area
to
D31
D32 D32
to CPU No.2 receive area CPU No.2 receive area
D63
D64 D64
CPU No.3 send data CPU No.3 send data
to
D95