Cisco TelePresence System Codec C40 Reference Manual page 39

Cisco TelePresence System Codec C40/C60
Contents Introduction
xConfiguration Conference [1..1] MaxTransmitCallRate
Specify the maximum transmit bit rate to be used when placing or receiving calls. Note that this is
the maximum bit rate for each individual call; use the Conference MaxTotalTransmitCallRate setting
to set the aggregated maximum for all simultaneous active calls.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: xConfiguration Conference 1 MaxTransmitCallRate: 6000
xConfiguration Conference [1..1] MaxReceiveCallRate
Specify the maximum receive bit rate to be used when placing or receiving calls. Note that this is
the maximum bit rate for each individual call; use the Conference MaxTotalReceiveCallRate setting
to set the aggregated maximum for all simultaneous active calls.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: xConfiguration Conference 1 MaxReceiveCallRate: 6000
xConfiguration Conference [1..1] MaxTotalTransmitCallRate
This configuration applies when using a video system's built-in MultiSite feature (optional) to host a
multipoint video conference.
Specify the maximum overall transmit bit rate allowed. The bit rate will be divided fairly among all
active calls at any time. This means that the individual calls will be up-speeded or down-speeded as
appropriate when someone leaves or enters a multipoint conference, or when a call is put on hold
(suspended) or resumed.
The maximum transmit bit rate for each individual call is defined in the Conference
MaxTransmitCallRate setting.
Requires user role: ADMIN
Value space: <64..10000>
Range: Select a value between 64 and 10000.
Example: xConfiguration Conference 1 MaxTotalTransmitCallRate: 10000
D14642.15 Codec C40-C60 API Reference Guide TC7.0, JANUARY 2014.
About the API xConfiguration xConfiguration
xConfiguration Conference [1..1] MaxTotalReceiveCallRate
xConfiguration Conference [1..1] VideoBandwidth Mode
xConfiguration Conference [1..1] VideoBandwidth MainChannel Weight
39
xCommand
This configuration applies when using a video system's built-in MultiSite feature (optional) to host a
multipoint video conference.
Specify the maximum overall receive bit rate allowed. The bit rate will be divided fairly among all
active calls at any time. This means that the individual calls will be up-speeded or down-speeded as
appropriate when someone leaves or enters a multipoint conference, or when a call is put on hold
(suspended) or resumed.
The maximum receive bit rate for each individual call is defined in the Conference
MaxReceiveCallRate setting.
Requires user role: ADMIN
Value space: <64..10000>
Range: Select a value between 64 and 10000.
Example: xConfiguration Conference 1 MaxTotalReceiveCallRate: 10000
Set the conference video bandwidth mode.
Requires user role: ADMIN
Value space: <Dynamic/Static>
Dynamic: The available transmit bandwidth for the video channels are distributed among the
currently active channels. If there is no presentation, the main video channels will use the
bandwidth of the presentation channel.
Static: The available transmit bandwidth is assigned to each video channel, even if it is not active.
Example: xConfiguration Conference 1 VideoBandwidth Mode: Dynamic
The available transmit video bandwidth is distributed on the main channel and presentation channel
according to "MainChannel Weight" and "PresentationChannel Weight". If the main channel
weight is 2 and the presentation channel weight is 1, then the main channel will use twice as much
bandwidth as the presentation channel.
Requires user role: ADMIN
Value space: <1..10>
Range: 1 to 10.
Example: xConfiguration Conference 1 VideoBandwidth MainChannel Weight: 5
API Reference Guide
xStatus Appendices
Copyright © 2010–2014 Cisco Systems, Inc. All rights reserved.