Cisco TelePresence System Codec C40 Reference Manual page 38

Cisco TelePresence System Codec C40/C60
Contents Introduction
xConfiguration Conference [1..1] DoNotDisturb DefaultTimeout
This setting determines the default duration of a Do Not Disturb session, i.e. the period when
incoming calls are rejected and registered as missed calls. The session can be terminated earlier
by using the user interface (remote control or Touch screen control panel) or the Conference
DoNotDisturb Mode setting. The default value is 60 minutes.
Requires user role: ADMIN
Value space: <0..1440>
Range: Select the number of minutes (between 0 and 1440, i.e. 24 hours) before the Do Not
Disturb session times out automatically.
Example: xConfiguration Conference 1 DoNotDisturb DefaultTimeOut: 60
xConfiguration Conference [1..1] FarEndControl Mode
Lets you decide if the remote side (far end) should be allowed to select your video sources and
control your local camera (pan, tilt, zoom).
Requires user role: ADMIN
Value space: <Off/On>
Off: The far end is not allowed to select your video sources or to control your local camera (pan,
tilt, zoom).
On: Allows the far end to be able to select your video sources and control your local camera (pan,
tilt, zoom). You will still be able to control your camera and select your video sources as normal.
Example: xConfiguration Conference 1 FarEndControl Mode: On
xConfiguration Conference [1..1] FarEndControl SignalCapability
Set the far end control (H.224) signal capability mode.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the far end control signal capability.
On: Enable the far end control signal capability.
Example: xConfiguration Conference 1 FarEndControl SignalCapability: On
D14642.15 Codec C40-C60 API Reference Guide TC7.0, JANUARY 2014.
About the API xConfiguration xConfiguration
xConfiguration Conference [1..1] Encryption Mode
xConfiguration Conference [1..1] DefaultCall Protocol
xConfiguration Conference [1..1] DefaultCall Rate
38
xCommand
Set the conference encryption mode. A padlock with the text "Encryption On" or "Encryption Off"
displays on screen for a few seconds when the conference starts.
NOTE: Requires the Encryption Option Key to be installed. When the Encryption Option Key is not
installed the encryption mode is set to Off.
Requires user role: ADMIN
Value space: <Off/On/BestEffort>
Off: The system will not use encryption.
On: The system will only allow calls that are encrypted.
BestEffort: The system will use encryption whenever possible.
> In Point to point calls: If the far end system supports encryption (AES-128), the call will be
encrypted. If not, the call will proceed without encryption.
> In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must support
encryption. If not, the conference will be unencrypted.
Example: xConfiguration Conference 1 Encryption Mode: BestEffort
Set the Default Call Protocol to be used when placing calls from the system.
Requires user role: ADMIN
Value space: <Auto/H323/Sip/H320>
Auto: Enables auto-selection of the call protocol based on which protocols are available. If multiple
protocols are available, the order of priority is: 1) SIP; 2) H323; 3) H320. If the system cannot
register, or the call protocol is not enabled, the auto-selection chooses H323.
H323: H323 ensures that calls are set up as H.323 calls.
Sip: Sip ensures that calls are set up as SIP calls.
H320: H320 ensures that calls are set up as H.320 calls (only applicable if connected to a Cisco
TelePresence ISDN Link gateway).
Example: xConfiguration Conference 1 DefaultCall Protocol: H323
Set the Default Call Rate to be used when placing calls from the system.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: xConfiguration Conference 1 DefaultCall Rate: 1920
API Reference Guide
xStatus Appendices
Copyright © 2010–2014 Cisco Systems, Inc. All rights reserved.