Controls, Connectors And Indicators - Bosch Plena Voice Alarm System Installation And Operation Manual

Plena Voice Alarm System
3.2.7

Controls, connectors and indicators

Figure 3.2 Front and rear views of the voice alarm controller
See Figure 3.2 for an overview of the controls, connections and indicators on the voice alarm
controller:
1.
2.
3.
4.
Bosch Security Systems B.V.
1 2
Plena Voice Alarm Controller
Fault Indicators Disabled
A B
0 dB
Processor reset Mains
Battery
-6dB Network
Call/EMG Message
-20dB
Music/Spare
EMG mic
Ground short RCP
Input Router
Alert message
Alarm message Indicator test
EMG mic
13
17 16 15 14
18 19 20
1 Channel 2 Channel
Int Booster BGM/ C all BGM/ Spare
Ext Booster
N.C ./Spare Call
Override/Trigger Output
A B
24V
100V
100V NC
Z1
Z1 Z1 EM G
COM
0 0
NO
Z2
100V
100V NC
Z2 Z2
COM Fault
0 0 Z3
NO
100V
100V
NC
Z3 Z3 Z4
C all
COM
0 0
NO
Z5
100V
100V
NC
Z4 Z4
24V Volume Override
0 0
Z6
NO
100V 100V
Z5 Z5
TRG 1 TRG2
0 0
100V 100V Out
Z6 Z6
0
0
Ext 100V 100V
Int
B ooster
In B ooster
0 70 V
Out
0
GND
DC In 24V
10 0V C all out
External Booster
47 46 45 44 43
Power LED/VU Meter:
A combined power indicator and VU meter. The green power LED is lit if the voice alarm
controller is connected to the mains or back-up power and switched on. The VU meter
indicates the master VU level: 0 dB (red), 6 dB, -20 dB (yellow).
Fault indicators:
Twelve yellow system fault LEDs (Processor reset, Network, Call/EMG, Music/Spare,
Ground short, Input, Mains, Battery, Message, EMG mic, RCP and Router) and twelve
yellow loudspeaker line fault LEDs. Fault indication is only possible if supervision is
enabled (see section 7.5.3 ). If supervision is disabled, the yellow Disabled LED is lit.
Fault state buttons:
Two buttons to acknowledge (Ack) and reset (Reset) the fault state (see section 7.5 ).
Emergency state buttons:
Two buttons to acknowledge (Ack) and reset (Reset) the emergency state (see section
7.4 ).
Installation and Operation manual
3 4
Fault EMG
Zone1
Zone2 Ack
Zone3
Zone select
Zone4
Zone5
Reset
Zone6
Zone1
Select Zone select
All call
CD/Tuner Aux
+
-
0
- +
10
12 11 9 8 7
21 22
Trigger input/24V DC out
Emergency 24V
1 2 3 4 5 6 DC out
10 k 10 k
Business VO X
1 2 3 4 5 6
Switch
Call station For ser vice only
NC NO
24V
1 2 3 4 5 6
COM DC out
1
2
1 2 3 4 5 6
VOX Switch
In
L
R
CD/Tuner AUX PC
42 41 40 39
System overview | en
5
Zone2 Zone3 Zone4
6
23 24 25 26 27 28
LBB 1 990/00 8900 199 0 0001
Plena Voice Alarm Controller
Max. output power 360W
Rated output power 240W
115-230V~, 50/60Hz
S/N.
N6 63
Design & Quality
The Netherlands
SEL1 Monitor
SEL0 APR mode
Supervision
Firmware
2ch operation
Upgrade
Reserved USB
Off Off
On On
Line fuse
Impedance
T6.3L250V for230V AC
Calibration
T10L250V for115V AC
Remote Control Panel
Vox
GND
Speech filter EMG. Mic
Phantom power
Off
Mic/Line
On
Digital Monitoring
Vox
Mess age Speaker
38 37 36 35
9922 141 1037x (V2.16) | V0.6 | 2011.09
15
Alarm
Zone5 Zone6
29 30 31
115V~ 230V~
Apparatus delivered
C onnected for 230V~
Power
Reserved
Rated input power :760VA
Reserved
1
Router
2
W arning
This apparatus must be earthed
34 33 32