Table of Contents
Advertisement
2. CONTROLS, INDICATORS AND CONNECTORS
2-3 Left Side Section
q
w
e
1
Cassette cover
Pressing the EJECT switch on top of the section opens this
cover so that a videocassette can be inserted or removed
from the unit. The cover can be locked automatically by
pushing and closing it.
• If the cassette cover is not closed, the GY-DV700W will
remain inoperative.
Memo:
To prevent penetration of foreign objects into the unit,
do not leave the unit with the cassette cover open.
2
[MONITOR OUT] monitor output connector (BNC)
• Composite video signal output connector.
Setup level signals are output.
• An EE image or the playback image is output through
the VCR section.
An EE image is output during other modes than the
playback mode.
* Data for the Camera menus and VCR setup menus or
time code is not output.
• A setup level signal is not attached to the IEEE 1394
signal's EE image.
3
[Y/C OUT] connector (4P)
Separate YC video signal output connector.
When setting to WIDE mode or playing back a tape that
was recorded in the WIDE mode, an ID signal for identifying
the WIDE screen mode is output superimposed on the video
signal.
4
[TC IN] connector (BNC)
Input connector for the SMPTE-standard LTC signal. The
built-in time code generator can be slave-locked with the
input time codes.
If the user's bits should also be slave-locked, set the VCR
Setup Menu item No. 403 U-BIT SLAVE to "TC&UB".
* When the REC/FREE switch (8 on page 15) is set to
REC, or the VCR Setup Menu item No. 398 SSF MODE
is set to "CUE MODE" or "MARK MODE", slave-locking
will not take place.
For the slave lock of time code, see page 58.
5
TC OUT connector (BNC)
Output connector for the LTC signal from the built-in time
code generator.
The time code recorded on the tape is not output in play mode.
6
[LINE OUT CH-1/CH-2] connector (RCA)
Output connector for audio signals.
• Outputs the input audio signal in the record and stop
modes.
18
PUSH
DV CAMCORDER
GY-DV700W
Y/C OUT MONITOR OUT LINE OUT
CH-1
CH-2
VTR
REMOTE
TC IN
TC OUT
r t y
SYNC IN
TEST OUT
MIC IN
LENS
• Outputs the playback audio signal in the playback mode.
• Alarm sound is not output.
7
[TEST OUT] connector (BNC)
Composite video signal output connector.
Outputs the camera image.
Setup level signals are output.
8
[SYNC.IN] connector (BNC)
For inputting the sync signal when the GY-DV700W's
camera image is synchronized with an external component.
Memo:
• The camera cannot be synchronized with a VCR
playback signal.
• When the power is switched ON while an external sync
signal is input, the screen moves in a vertical direction
for a few seconds. This is not a malfunction.
• Only for the combined H (horizontal)/V (vertical)
synchronizing signal. Synchronization with the SC (sub-
carrier) of the input signal is not possible.
Even if SC adjustment is performed, a phase shift will
take place at the time of power on/off. The SC phase
must be adjusted each time the power is turned on.
• If the external sync signal is disrupted during recording,
the "SYnc inh" (SYNC INHIBIT) indicator is displayed
on the counter display and recording stops.
• If the external sync signal is disrupted during playback,
playback of the disturbed video image continues.
Start playback again after synchronization is obtained
and the signal is stabilized.
9
[VTR REMOTE] connector
A part of the unit's functions can be controlled externally.
To remote control the unit using the control signal of this
connector, the VCR Setup Menu item No. 050 REMOTE
SELECT must be set to "RS232C".
For details, please consult your JVC dealer.
Note:
• When a cable is connected to the VTR REMOTE
connector, the VTR Setup Menu is not displayed in
the viewfinder. Make settings on the VTR Setup Menu
while the cable is not connected.
• When a cable is connected to the VTR REMOTE
connector, the VCR operation mode will not be
displayed correctly on the Status 1 screen in the
viewfinder.
0
Microphone attachment holes
For attaching the microphone holder KA-A50 (optional).
See "Attaching the Microphone (optional)" on page 32.
!0
o
i
u
Advertisement
Table of Contents
