Table of Contents
Advertisement
8. PLAYBACK MODE
8-1 Playback Procedure
FILTER
1 3200k
2 5600k+1/8ND
3 5600k
4 5600k+1/64ND
SHUTTER
C
MENU
AUTO IRIS
BACK L
NORMAL
SPOT L
1.
POWER switch
Operation
1.
Set the POWER switch to ON.
2.
Load the recorded videocassette correctly.
• Slide the EJECT switch to the side. When the cassette
cover opens, insert the videocassette and then close the
cassette cover again.
When a recordable videocassette (with the switch on the
back of the cassette set to REC) is loaded, the unit enters
the record-pause mode (STBY mode).
In this case, press the STOP button to release the record-
pause mode.
3.
Press the PLAY button.
a
The LED indicator above the PLAY button lights and
playback starts.
• During playback of a recording made in the WIDE (16:9
picture) mode, the "WIDE" indicator is displayed in the
counter display. The "WIDE" indicator is not shown if the
recording was made in the NORMAL (4:3 picture) mode.
CH 1
40 30
20
CH 2
32k
48k
SLAVE
SP
AUD LOCK
WIDE
MENU
"WIDE" indicator
4.
Press the STILL button to stop playback temporarily.
a The LED indicator above the STILL button lights
and the unit enters the still mode.
5.
To re-start playback, press the PLAY button.
a The LED indicator above the STILL button goes
out and playback starts again.
6.
To stop playback, press the STOP button.
a The LED indicator above the PLAY button goes
out and the unit enters the stop mode.
54
2.
OPERATE/WARNING
LIGHT
RESET
ON
OFF
MONITOR
SELECT
COUNTER
CTL
ALARM
TC
UB
STATUS
MONITOR
CH-1
AUDIO
CH-2
LEVEL
FULL AUTO BLACK
LOLUX
STRETCH
NORMAL
COMPRESS
NG
POWER
ON
OFF
OVER
AUTO OFF DEW
10
0 dB
SERVO
RF
L i
OVER
PB
NDF
HOLD
H
M
S
F
2.
EJECT switch
EJECT
LOG
REW
STOP
FF
6.
STOP button
3.
5.
CAUTION:
• When the still picture mode or stop mode has continued
for about 30 minutes, the unit automatically switches to
the save mode to protect the tape.
The time until the tape protect mode is initiated can be
set to 3 or 30 minutes with the VCR Setup Menu item
No. 307 LONG PAUSE TIME.
When used in a cold environment, the setting will be 3
minutes regardless of the setting on the VCR Setup
Menu.
• Noise may appear in the picture during still mode.
• When the automatic tracking function is activated at the
start of the playback mode, digital noise may appear on
the playback image.
• This unit does not allow manual tracking adjustment.
• When playing back a tape recorded on another unit,
digital noise may appear during playback.
• When turning on the power with the tape inserted or
after loading a tape, the built-in head cleaner will emit a
sound while operating. This does not indicate a malfunc-
tion.
Memo:
• If a tape recorded in the WIDE mode is played back on a
4:3 aspect ratio monitor TV, it is displayed as a squeezed
image (stretched vertically).
4:3 aspect ratio monitor 16:9 aspect ratio monitor
• When playing back a tape that is recorded in the WIDE
mode, an ID signal for identifying the WIDE screen mode
is output via the Y/C OUT connector superimposed on
video signal.
PLAY
STILL
4.
STILL button
PLAY button
Playback of tape recorded
in WIDE mode
Advertisement
Table of Contents
